Vendlet 6000000 User Manual Download Page 51 | Manualshive

Page: 51 / 56

background image

51

PART 3 - Technical manual

Replacing the actuator

1. Disconnect the power cable from the

mains outlet.

2. Disconnect the cable from the control

unit.

3. Disconnect the actuator cable from the

control unit and release it from the bed,
allowing it to hang freely.

4. Remove the 2 Allen screws securing the

actuator to the actuator fitting and

remove the actuator.

5. Remove the actuator cable from the

defective actuator if you want to re-use
the cable. The actuator cable is attached
to the actuator with a locking device.
Release the locking device by pressing a
small straight blade screwdriver against
the side of the locking device on both
sides.

6. Remove the actuator cable from the

defective actuator and install it on the
new actuator.

7. Mount the new actuator on the actuator

fitting and attach it using the two Allen
screws.

8. Secure the actuator cable with two new cable ties and route it along the inside

of the bed frame to the control unit. Use cable ties to secure the actuator cable
along the bed frame in such a way that the cable will not get caught by the

moving parts of the bed. See section ” Routing actuator cables (including cable
ties)” for further details.

9. Reconnect the power cable to the mains outlet.

10. Reset the system by simultaneously pressing the two top buttons on the hand

control. You will hear a series of rhythmic beeps. Press and hold the buttons until
the beeping stops.

11. Check whether the actuator is working properly.

Remove the Allen screws and free the

actuator

Release the locking device

«
...
49
50
51
52
53
...
»

Summary of Contents for 6000000

























































Reviews:

No comments

Related manuals for 6000000

Brand: UnionSpecial Pages: 56

Brand: ICS Schneider Messtechnik Pages: 124

Brand: DARKSTAR TECHNOLOGIES Pages: 4

Brand: TDW Pages: 2

Brand: Taurus Pages: 25

Brand: Vancare Pages: 3

Brand: Paitec Pages: 14

Brand: Launch Pages: 3

Brand: Launch Pages: 43

Brand: Launch Pages: 8

Brand: Launch Pages: 67

Brand: Launch Pages: 55

Brand: LAUNCH TECH Pages: 14

X-431 PROS V4.0

Brand: Launch Pages: 80

Brand: M-Audio Pages: 25

Marathon Multi600

Brand: Saeyang Pages: 21

Brand: S&C Pages: 11

Brand: Yamaha Pages: 139

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands