manualshive.com logo in svg

VCS VideoJet 10, Manual

Share
Download
VCS VideoJet 10 Manual Download Page 42

Configuration with web browser

44

VideoJet 10

Save general logfile to hard disk:

Select this option to store the logfile in a text file on the local com-
puter.

These text files can be viewed in the usual Office programs (for 
example, MS Word or MS Excel), and printed out.

Path for saving alarm messages:

Enter here the path to the location where the log files for the alarm 
messages are to be stored.

"

If necessary, click on the button 

Search 

in order to find a suitable 

folder.

File for saving general messages:

Enter here the path to the location where the log files for the general 
system messages are to be stored.

"

If necessary, click on the button 

Search 

in order to find a suitable 

folder.

Path for JPEG an MPEG files:

Enter here the path to the storage location for the individual images 
and MPEG recordings which can be stored from the Live page.

"

If necessary, click on the button 

Search 

in order to find a suitable 

folder.

Summary of Contents for VideoJet 10







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands