manualshive.com logo in svg

VCS VideoJet 10, Manual

Share
Download
VCS VideoJet 10 Manual Download Page 14

Product Description

16

VideoJet 10

Summary

The main functions of the VideoJet 10 can be summarized as 
follows:

!

Video, audio and data transmission via IP data nets

!

Multicast function for simultaneous transmission to a number of 
receivers

!

Analog BNC composite video input (PAL/NTSC) (transmitter)

!

Analog BNC composite video output (PAL/NTSC) (receiver)

!

One audio input/output (mono)

!

Video and audio encoding to the international standard MPEG- 4

!

Integrated Ethernet interface (10/100 Base-T)

!

CompactFlash interface for memory card or wireless LAN card. 

!

Two transparent bidirectional data channels via serial interface 
ports RS232/RS422/RS485 and RS232

!

Remote control of all internal functions via TCP/IP

!

Password protection to prevent unauthorized connection or 
alterations to configuration

!

Closed contact input for external sensor (e.g. door contact)

!

Closed contact output for external equipment (e.g. lights or 
acoustic alarms)

!

Event driven automatic connection setup (e.g. on switch-on and 
with alarms)

!

Rapid and user friendly configuration via web browser

!

Firmware update through flash memory

!

Comfortable configuration upload 

Summary of Contents for VideoJet 10







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands