manualshive.com logo in svg

VCS VideoJet 10, Manual

Share
Download
VCS VideoJet 10 Manual Download Page 21

Installation

23

VideoJet 10

Switching on/off

Mains connection

Included with the VideoJet 10 is a power supply unit.

The VideoJet 10 is not provided with a power switch. The unit is 
ready for operation as soon as the unit is connected to the power. 

"

Insert the mains socket into the connector 

Power

.

"

Connect the plug-in power supply into an earthed socket. 
During the start the LED 

Power

 lights up red. The device is ready 

as soon as the LED Power lights up green. 

If the network connection has also been established correctly, the 
green LED 

L 

also lights up. A flashing yellow LED 

T 

signals the 

transport of data packages over the network.

Warning!

Use only the plug-in power supply unit supplied for operation of the 
VideoJet 10. Ensure that the mains supply is free from interference 
such as over voltages, spikes, or brownouts by using suitable mains 
conditioners where necessary. 

Only connect the VideoJet 10 to the power source after all other 
connections have been established.

Summary of Contents for VideoJet 10







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands