VAT Series 651 Installation, Operating, & Maintenance Instructions Download

Page: 5 / 53

Installation, Operating & Maintenance Instructions

Series 651 DN 320-400 (I.D. 12“ - 16”), Logic

VAT Vakuumventile AG, CH-9469 Haag, Switzerland

Tel +41 81 771 61 61 Fax +41 81 771 48 30 [email protected] www.vatvalve.com

267736ED

2008-02-26

5/53

Valve unit

Pressure range at 20

- Aluminum

(651 . . - . A . . - . . . . ) 1 x 10E-8 mbar to 1.2 bar (abs)

- Aluminum hard anodized (651 . . - . H . . - . . . . ) 1 x 10E-6 mbar to 1.2 bar (abs)

- Aluminum nickel coated (651 . . - . I . . - . . . . )

1 x 10E-8 mbar to 1.2 bar (abs)

Leak rate to outside at 20

- Aluminum

(651 . . - . A . . - . . . . ) 1 x 10E-9 mbar l/s

- Aluminum hard anodized (651 . . - . H . . - . . . . ) 1 x 10E-5 mbar l/s

- Aluminum nickel coated (651 . . - . I . . - . . . . )

1 x 10E-9 mbar l/s

Leak rate valve seat at 20

- Aluminum

(651 . . - . A . . - . . . . ) 1 x 10E-9 mbar l/s

- Aluminum hard anodized (651 . . - . H . . - . . . . ) 1 x 10E-4 mbar l/s

- Aluminum nickel coated (651 . . - . I . . - . . . . )

1 x 10E-9 mbar l/s

Cycles until first service
- Isolation cycles (open - closed - open)
- Throttling cycles (open - max. throttle - open)

200’000 (unheated and under clean conditions)
1’000’000 (unheated and under clean conditions)

Admissible operating temperature

10°C to +150°C

Mounting position

horizontally only

Wetted materials

- Body

(651 . . - . A . . - . . . . ) Aluminum 3.2315 (AA6082)

- Body

(651 . . - . H . . - . . . . ) Aluminum 3.2315 (AA6082) hard anodized

- Body

(651 . . - . I . . - . . . . )

Aluminum 3.2315 (AA6082) nickel coated

- Pendulum plate

(651 . . - . A . . - . . . . ) Aluminum 3.2315 (AA6082), 1.4310 (301), PTFE

- Pendulum plate

(651 . . - . H . . - . . . . ) Aluminum 3.2315 (AA6082) hard anodized, 1.4310 (301), PTFE

- Pendulum plate

(651 . . - . I . . - . . . . )

Aluminum 3.2315 (AA6082) nickel coated, 1.4310 (301), PTFE

- Sealing ring

(651 . . - . A . . - . . . . ) Aluminum 3.2315 (AA6082),

1.4306 (304L)

- Sealing ring

(651 . . - . H . . - . . . . ) Aluminum 3.2315 (AA6082) hard anodized, 1.4306 (304L)

- Sealing ring

(651 . . - . I . . - . . . . )

Aluminum 3.2315 (AA6082) nickel coated, 1.4306 (304L)

ther parts

Stainless steel 316L (1.4404 or 1.4435), 1.4122, 1.4310 (301),
1.4303 (304), 1.4571, A2 (304)

- Seals

Viton

(standard). Other materials available.

Seal materials are declared on dimensional drawing of specific valve ordering
number.

DN 320

12"

(65150 - ....)

DN 350

14"

(65151 - ....)

DN 400

16"

(65152 - ....)

Max. differential pressure on plate during isolation

1200 mbar in either

direction

1200 mbar in either

direction

1200 mbar in either

direction

Max. differential pressure on plate
during opening and throttling

5 mbar

Min. controllable conductance

molecular flow)

3.2 l/s

3.5 l/s

4.0 l/s

Dimensions

Refer to dimensional drawing of specific valve ordering number

(available on request)

Summary of Contents for Series 651






















































Search results

Summary of Contents for Series 651

Reviews:

Related manuals for Series 651

Brands by name

Popular brands

VAT Series 651, Installation, Operating, & Maintenance Instructions

Search results

Summary of Contents for Series 651

Reviews:

Related manuals for Series 651

Brands by name

Popular brands