VAT Series 651 Installation, Operating, & Maintenance Instructions Download

Page: 42 / 53

Installation, Operating & Maintenance Instructions

Series 651 DN 320-400 (I.D. 12“ - 16”), Logic

VAT Vakuumventile AG, CH-9469 Haag, Switzerland

Tel +41 81 771 61 61 Fax +41 81 771 48 30 [email protected] www.vatvalve.com

267736ED

2008-02-26

42/53

D e s c r i p t i o n

Required tool

25. Remove actuator shaft seals

carefully with a soft tool.

26. Clean actuator feedthrough with

alcohol.

27. Lubricate each o-ring groove with

0.1 ml vacuum grease. Pay attention
that grease is distributed constantly
over the whole circumference.

•

Soft tool

(o-ring remover)

•

Vacuum grease

28. Clean or replace seals if necessary.

Lubricate each o-ring with 0.05 ml
vacuum grease.

29. Install o-rings.

30. Deposit 0.1 ml vacuum grease on

each o-ring. Pay attention that
grease is distributed constantly over
the whole circumference.

31. Remove fixation kit and mounting

screw for pendulum plate.

32. Clean screw and slightly lubricate

thread with 0.1 ml vacuum grease,
then reinstall fixation kit.

33. Clean actuator shaft and lubricate it

with 0.1 ml vacuum grease.

34. Install actuator

•

Tighten actuator screws with 6 Nm.

•

Remove vacuum grease from

actuator shaft face after installation.

Allen Wrench

5mm

35. Install controller

•

Tighten the controller screws with

1 Nm.

•

Connect cables at controller

•

Connect compressed air at
actuator

Allen Wrench

4mm

Summary of Contents for Series 651






















































Search results

Summary of Contents for Series 651

Reviews:

Related manuals for Series 651

Brands by name

Popular brands

VAT Series 651, Installation, Operating, & Maintenance Instructions

Search results

Summary of Contents for Series 651

Reviews:

Related manuals for Series 651

Brands by name

Popular brands