VAT Series 651 Installation, Operating, & Maintenance Instructions Download

Page: 40 / 53

Installation, Operating & Maintenance Instructions

Series 651 DN 320-400 (I.D. 12“ - 16”), Logic

VAT Vakuumventile AG, CH-9469 Haag, Switzerland

Tel +41 81 771 61 61 Fax +41 81 771 48 30 [email protected] www.vatvalve.com

267736ED

2008-02-26

40/53

D e s c r i p t i o n

Required tool

gate

seal

10. Remove gate and body o-ring from

sealing ring carefully with a soft tool.

11. Remove grease residues at sealing

ring with alcohol.
Clean sealing ring and pendulum
plate with alcohol or in an ultrasonic
bath.

12. Clean out valve body with alcohol.

Use an appropriate non metal tool
with a cloth to enter valve body.
Do not enter valve body with hands!

Then blow out valve body with clean
air.

Do not directly expose seals
(actuator and retaining pin
feedthroughs) to air stream!

13. Clean or replace gate seal if

necessary.
Install gate o-ring to sealing ring
without grease.

body

seal

Valve size

Quantity of grease [ml]

DN320 / 12”

(65150 - . . . . - . . . .)

0.3

DN350 / 14”

(65151 - . . . . - . . . .)

0.4

14. Clean or replace body seal if

necessary.
Lubricate body o-ring with the
quantity of vacuum grease listed in
the table to the right.

DN400 / 16”

(65152 - . . . . - . . . .)

0.4

15. Install body o-ring into sealing ring.

Valve size

Quantity of grease [ml]

DN320 / 12”

(65150 - . . . . - . . . .)

0.5

DN350 / 14”

(65151 - . . . . - . . . .)

0.7

16. Deposit vacuum grease on the

bottom side of the body seal
according to drawing below. Pay
attention that the quantity of vacuum
grease listed in the table to the right
is distributed constantly over the
whole circumference.

DN400 / 16”

(65152 - . . . . - . . . .)

1.1

Note: For Replacement of actuator
or actuator shaft seals, proceed with
step 18 otherwise go to step 17.

17. Reassembly the valve in reverse

order, step 9…3.

18. Close the valve bonnet, see step 40.

Apply grease deposit
on this side

Summary of Contents for Series 651






















































Search results

Summary of Contents for Series 651

Reviews:

Related manuals for Series 651

Brands by name

Popular brands

VAT Series 651, Installation, Operating, & Maintenance Instructions

Search results

Summary of Contents for Series 651

Reviews:

Related manuals for Series 651

Brands by name

Popular brands