VAT Series 651 Installation, Operating, & Maintenance Instructions Download

Page: 35 / 53

Installation, Operating & Maintenance Instructions

Series 651 DN 320-400 (I.D. 12“ - 16”), Logic

VAT Vakuumventile AG, CH-9469 Haag, Switzerland

Tel +41 81 771 61 61 Fax +41 81 771 48 30 [email protected] www.vatvalve.com

267736ED

2008-02-26

35/53

4 Trouble

shooting

Failure

Check

Action

No dots lighted on display

24 V power supply ok?

Connect valve to power supply according to

«Electrical connection» and make sure that power supply
is working.

Local operation via service

port active

Switch to remote operation.

Remote operation does not work

Safety mode active, check for

D on display?

Provide power to motor to allow for operation.

Refer to «Electrical connection» for details.

Display shows «E 20»
(fatal error - limit stop of valve
unit not detected)

Replace actuator according to
«Maintenance procedures».

Display shows «E 22»

(fatal error - rotation angle of
valve plate limited during
operation)

Valve plate mechanically

obstructed?

Resolve obstruction.

Display shows «E 40»

(fatal error - motor driver failure
detected)

Replace control unit according to

«Maintenance procedures».

Display shows «D C» or
«D999»

Motor Interlock is open

Motor power supplied?

Provide power to motor to allow for operation.

Refer to «Electrical connection» for details.

Display shows «SR»

(Service Request)

Valve unit heavy

contaminated or gate seal
heavyly sticking?

Clean valve and/or replace gate seal according to

«Maintenance procedures».

CLOSE VALVE does not work

Safety mode active, check for

D on display?

Maintenance mode active

Provide power to motor to allow for operation.

Refer to «Electrical connection» for details.

Refer to “Display shows «

M C»” in this table

OPEN VALVE does not work

Safety mode active, check for

D on display?

Maintenance mode active

Provide power to motor to allow for operation.

Refer to «Electrical connection» for details.

Refer to “Display shows «

M100»” in this table

Display shows «M C»

Maintenance mode active

Pin 14 of service connector is connected to ground. Plate

will close. Further movement of plate is blocked.

Display shows «M100»

Maintenance mode active

Pin 13 of service connector is connected to ground. Plate

will open. Further movement of plate is blocked.

Safety mode active, check for

D on display?

Provide power to motor to allow for operation.

Refer to «Electrical connection» for details.

POSITION CONTROL does not
work

POSITION CONTROL

selected, check for V on
display?

Select POSITION CONTROL mode.

Refer to «Position control» for details.

COMPRESSED AIR FAILURE

No or too less air pressure on

air input of valve

Connect air or increase air pressure. Make sure that the air

pressure is more than 4 bar (55 psi).

1)Priority of pin 14 is higher than pin 13. If pin 14 is connected to ground after pin 13 the valve will close.
Ground of service connector is at pin 4 and 8.

Summary of Contents for Series 651






















































Search results

Summary of Contents for Series 651

Reviews:

Related manuals for Series 651

Brands by name

Popular brands

VAT Series 651, Installation, Operating, & Maintenance Instructions

Search results

Summary of Contents for Series 651

Reviews:

Related manuals for Series 651

Brands by name

Popular brands