VAT Series 651 Installation, Operating, & Maintenance Instructions Download | Manualshive

Page: 37 / 53

background image

Installation, Operating & Maintenance Instructions

Series 651 DN 320-400 (I.D. 12“ - 16”), Logic

VAT Vakuumventile AG, CH-9469 Haag, Switzerland

Tel +41 81 771 61 61 Fax +41 81 771 48 30 [email protected] www.vatvalve.com

267736ED

2008-02-26

37/53

5

Maintenance & repairs

Under clean operating conditions, the valve does not require any maintenance during the specified cycle life.
Contamination from the process may influence the function and requires more frequent maintenance.

Before carrying out any maintenance or repairs, please contact VAT. It has to be individually decided whether the
maintenance/repair can be performed by the customer or has to be carried out by VAT. The fabrication number on the
valve

made in Switzerland
Fabrication No.:

patented

. .

. . . . . – . . . . – . . . . / . . . .

A – . . . . . .

Fabrication number

has always to be specified.

All supplies (e. g. compressed air, electrical power) must be disconnected for removal/installation of the valve from/into
the system.

Even with disconnected supply, loaded springs and/or air cushions in cylinders can be potential hazards.

Keep fingers and objects away from the valve opening!

Products returned to VAT must be free of harmful substances such as e.g. toxical, caustic or micro-biological ones. If
products are radioactively contaminated, fill in the VAT form «Contamination and Radiation Report» and send it with the
product. The form is available at VAT. The maximum values indicated in the form must not be exceeded.

«
...
35
36
37
38
39
...
»

Summary of Contents for Series 651






















































Reviews:

No comments

Related manuals for Series 651

Brand: ABB Pages: 52

Brand: ZKTeco Pages: 18

Brand: EAE Pages: 36

Brand: D+H Pages: 36

Brand: D-Box Pages: 4

Brand: D+H Pages: 36

Brand: Fantech Pages: 2

Brand: National Instruments Pages: 29

Brand: Häfele Pages: 2

Brand: Häfele Pages: 24

Brand: Lawler Pages: 4

Brand: QTP Pages: 2

Brand: PESA Pages: 30

Brand: Linear Technology Pages: 7

J1000 CIMR-JC series

Brand: YASKAWA Pages: 25

FAREX SR MINI SYSTEM

Brand: RKC INSTRUMENT Pages: 82

Brand: Fancom Pages: 23

Brand: Beninca Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands