VAT Series 651 Installation, Operating, & Maintenance Instructions Download Page 15 | Manualshive

Page: 15 / 53

background image

Installation, Operating & Maintenance Instructions

Series 651 DN 320-400 (I.D. 12“ - 16”), Logic

VAT Vakuumventile AG, CH-9469 Haag, Switzerland

Tel +41 81 771 61 61 Fax +41 81 771 48 30 [email protected] www.vatvalve.com

267736ED

2008-02-26

15/53

3 Operation

Operation is allowed after completion of the installation procedure only.

3.1 Introduction

This valve is designed for downstream pressure control in vacuum chambers. It can be employed in a pressure control
mode or a position control mode.
In both cases local or remote operation is possible.

3.1.1 Local

operation

Local operation means that the valve is operated via the service port using a computer or the Service Box 2. When using
a computer, a service cable and a software from VAT are required. You can either download our freeware 'Control View'
from

www.vatvalve.com

or purchase our 'Control Performance Analyzer'.

These software are beneficial especially for setup, testing and maintenance.

How to start: Connect service cable, start software and push button ‘LOCAL’ to enable for operation. Then enter menu
Setup/Sensor and do sensor configuration according to your application to make sure that you get the correct pressure
displayed.

‘Control view’ supports:

- parameter

setup

- manual

control

- numeric

monitoring

- basic

diagnostic

'Control Performance Analyzer'
supports:

- parameter

setup

- manual

control

- sequence

control

-

numeric and graphical
monitoring

- data

recording

- data

analysis

- advanced

diagnostic

When communication to service port is interrupted the valve will change to remote operation.
So when service cable will be disconnected or software will be shut down, the valve returns
automatically to remote operation.
This may result in an immediate movement of the valve depending on remote control.

Refer to «Spare parts / Accessories» for ordering numbers of service cable, software and Service Box 2.

«
...
13
14
15
16
17
...
»

Summary of Contents for Series 651






















































Reviews:

No comments

Related manuals for Series 651

Brand: Fagor Pages: 10

Brand: Fagor Pages: 358

Brand: Fagor Pages: 556

Brand: Fagor Pages: 172

Brand: Fagor Pages: 180

Brand: Fagor Pages: 112

Master Control Unit

Brand: FaderMate Pages: 36

Brand: Samson Pages: 32

Brand: Quantum Pages: 15

Brand: YOKOGAWA Pages: 2

ALICAT SCIENTIFIC PC

Brand: Halma Pages: 2

ALICAT SCIENTIFIC PCD

Brand: Halma Pages: 46

Brand: Rachio Pages: 2

Brand: Parkside Pages: 65

Brand: Ultratec Pages: 33

Brand: Simplex Pages: 40

PersonalWorkplace Pro Video

Brand: G&D Pages: 56

Brand: Beninca Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands