VANLEIGH PINECREST, Owner'S Manual

Page: 65 / 158

Rev: 06.28.18
Page 6
CCD-0001519
Standard Mode and Menu
To reach Standard Mode (Fig. 2) for leveling:
1. Power on the OneControl Touch Panel (Fig. 2L).
2. Press "MyRV Control Panel" on the main screen.
3. Press the "Leveler" icon.
4. The screen will show the system menu (Fig. 2) for Standard Mode. The front jacks can be extended/
retracted in Standard Mode. Rear jacks can only be retracted from this mode.
Basic Jack Operation
While in Standard Mode:
1. Press "RETRACT" (Fig. 2I) or "EXTEND" (Fig. 2J) and "FRONT" (Fig. 2A) to retract or extend front jacks.
2. Press "RETRACT" and "REAR" to retract rear jacks.
3. Press the "AUTO LEVEL" (Fig. 2M) button to start the auto leveling sequence.
4. Press the "AUTO HITCH" (Fig. 2N) button to start the hitch recognition sequence when reconnecting to
the tow vehicle.
5. Use the "UP" or "DOWN" arrow (Fig. 2B) buttons to cycle through the menu screen options:
A. Info: Scroll to "INFO" (Fig. 2C) and press "ENTER" (Fig. 2H) button to display system information,
e.g., angle, jack stroke or software version.
B. Auto Retract: Scroll to "AUTO RETRACT" (Fig. 2F) and press the "ENTER" button. Choose either
"ALL JACKS" or "REAR JACKS." Press the "ENTER" button again to start the "Auto Retract" sequence.
C. Manual Mode: Scroll to "MANUAL MODE" (Fig. 2G) and press "ENTER" button to start Manual
Level operation.
NOTE: Upon entering Manual Mode, a tutorial on operating the jacks will appear on the screen. Press "OK"
to clear the tutorial. To delete the tutorial, click the "Don't show this again" box in the bottom right
of the screen.
I. Press "EXTEND" (Fig. 3F) or "RETRACT" (Fig. 3E) and "FRONT" (Fig. 3B) to operate front jacks.
II. Press "EXTEND" or "RETRACT" and "REAR" (Fig. 3D) to operate rear jacks.
III. Press "EXTEND" or "RETRACT" and "RIGHT" (Fig. 3C) to operate right jacks.
IV. Press "EXTEND" or "RETRACT" and "LEFT" ( Fig. 3A) to operate left jacks.
NOTE: To operate jacks individually, press "EXTEND" or "RETRACT" then press the “LEFT” (Fig. 3A) or “RIGHT”
(Fig. 3C) button while simultaneously pressing the “FRONT" (Fig. 3B) or "REAR” button (Fig. 3D),
depending on which jack needs to be operated.
NOTE: If the rear jacks will not operate individually using the method described above, but they operate
properly when Auto Level is performed, the Twist Prevention Protection system has locked out the
operation to prevent damage to the frame of the trailer.
Operation - OneControl Touch Panel
Fig. 3
A
D
C
E F
B
Rev: 06.28.18
Page 7
CCD-0001519
Unhitching Instructions
NOTE: Prior to unhitching from the tow vehicle, ensure the trailer is parked on a level surface and chock the
tires of the trailer.
1. Extend the inner legs of both front jacks (landing gear) to within 4-5" of the ground by pulling on the
quick-release pins.
2. Push touch panel “ON/OFF” (Fig. 2L) to turn system on.
3. Press "MyRV Control Panel" on the main screen.
4. Press the "Leveler" icon.
5. The screen will show the system menu (Fig. 2) for Standard Mode. Push "EXTEND" (Fig. 2J) and "FRONT"
button (Fig. 2A) to extend front jacks and lift front of the trailer to take the weight of the trailer off of
the hitch.
6. Uncouple the trailer connection on the tow vehicle.
7. Pull the tow vehicle away and park at a safe distance.
Auto Level
1. After unhitching from the tow vehicle and parking the vehicle a safe distance away from the trailer,
press the “ON/OFF” button (Fig. 2L) if the OneControl Touch Panel is not on and then press “AUTO
LEVEL” (Fig. 2M).
NOTE: Once the automatic leveling cycle has been started, it is important that there is no movement in the
trailer until the leveling process is complete. Failure to remain still during the leveling cycle could
have an effect on the performance of the leveling system.
Auto Level Sequence
1. When Auto Level Sequence begins, the front of the trailer will seek a position near a level state.
2. Rear jacks will be grounded.
3. A side-to-side leveling sequence will occur.
NOTE: At this point on the 6 point system, the 2 middle jacks will be grounded to stabilize the trailer.
These 2 jacks do not level the trailer.
4. Each jack will perform a final grounding touch.
NOTE: If the AUTO LEVEL sequence does not perform as described above, locate the OneControl Touch
Panel inside the trailer or use the OneControl App to place the system in manual mode. Test that
the jacks operate correctly by pushing their corresponding buttons on the OneControl Touch Panel
or App; e.g., "FRONT" button operates only the front jacks, etc. (See "Operation - OneControl Touch
Panel" or "Operation - OneControl App" in this manual).
Hitch Recognition
1. Push touch panel “ON/OFF” (Fig. 2L) to turn system on.
2. Press "MyRV Control Panel" on the main screen.
3. Press the "Leveler" icon.
4. The screen will show the system menu (Fig. 2) for Standard Mode.
5. Press "AUTO HITCH" (Fig. 2N). Rear jacks will retract.
6. The front of the trailer will raise to the height where the auto level sequence was started.
NOTE: If the front of the trailer was below level when the Auto Level process was initiated, the hitch
recognition feature will retract the rear jacks but will not retract the front jacks to lower the trailer to
the initial hitch height. This feature helps prevent injury and/or damage to anything underneath the
trailer.
7. Connect tow vehicle and make sure trailer and hitch are connected and locked.
8. On the Standard Mode screen (Fig. 2) use the "UP" and "DOWN" arrows (Fig. 2B) to scroll to "AUTO
RETRACT" (Fig. 2F). Press "ENTER."
9. Choose "ALL JACKS." Press “ENTER." System will immediately retract all jacks.
Use the quick release pins on the landing gear to manually return the inner jack leg to the fully retracted position.
6 5