12
Technical Support: [email protected] US: +866 677 0053 EU: +44 (0) 1793 230 343
11. Advanced Remote
Control
IR Call Back and Third Party Control systems
Please note:
Due to the differing method of control
based on location, if you are using a third party
control system, learning the control from the IR is NOT
recommended as control will be limited to scrolling up/
down between inputs. For discrete source selection
you will need to import discrete hex codes for control
systems. These can be obtained through the Wyrestorm
website, by contacting our technical support or you can
input them manually.
For reference:
The IR is NEC and possesses a carrier
wave of 38KHz with a system code of 0x00
Controlling the MX0606/0808-PP using RS232 and
COMCTL PC Software
Typically, unless alternative methods of controlling
the matrix are chosen or problems with device
communication through the matrix encountered,
basic operation is all that is required to operate your
MX0606/0808-PP. However, the following information on
advanced operation will detail how the matrix system can
be configured and for advanced control and settings can
be altered or data manually input should such problems
arise, as well as configuring the system for third party
control.
RS232 Remote Control
Control of the matrix is possible through RS232 using
third party control systems or the dedicated Wyrestorm
COM CTL software included with your purchase (also
downloadable from www.wyrestorm.com).
RS232 Setting
Should third party control be required, please see below
for control system configuration and hex code input. The
RS232 connection on the matrix is female DB9. Users
can use USB-RS232 cable (supplied) for connection to
a PC or a straight through male-male (not supplied) for
connection to a control interface.
COM CTL
After fully connecting all inputs and outputs to the matrix
and installing the software, on opening the program
the control window will display information from the
matrix, such as messages received from the switch such
as input/output details, firmware version and control
commands/ASCII codes that allow the system to be
controlled remotely, as well as buttons used to navigate
the screen.
13
Technical Support: [email protected] US: +866 677 0053 EU: +44 (0) 1793 230 343
ADV
AN
CE
D R
E
M
O
TE CONTR
OL
11. Advanced Remote
Control
IR Call Back and Third Party Control systems
Please note:
Due to the differing method of control based on
location, if you are using a third party control system, learning the
control from the IR is NOT recommended as control will be limited
to scrolling up/down between inputs. For discrete source selection
you will need to import discrete hex codes for control systems.
These can be obtained through the Wyrestorm website, by
contacting our technical support or you can input them manually.
For reference:
The IR is NEC and possesses a carrier wave of
38KHz with a system code of 0x00
OUTPUT
CHANNEL
INPUT SELECT
1
2
3
4
5
6
7
8
0x1d 0x0d
0x1b 0x15
0x12 0x08
0x55 0x4a
0x06 0x03
0x07 0x02
0x44 0x51
0x1e 0x1a
Output1 source select key code:
0x80 0x81 0x82 0x83 0x84 0x85 0x86 0x87
Output2 source select key code:
0x90 0x91 0x92 0x93 0x94 0x95 0x96 0x97
Output3 source select key code:
0xa0 0xa1 0xa2 0xa3 0xa4 0xa5 0xa6 0xa7
Output4 source select key code:
0xb0 0xb1 0xb2 0xb3 0xb4 0xb5 0xb6 0xb7
Output5 source select key code:
0xc0 0xc1 0xc2 0xc3 0xc4 0xc5 0xc6 0xc7
Output6 source select key code:
0xd0 0xd1 0xd2 0xd3 0xd4 0xd5 0xd6 0xd7
Output7 source select key code:
0xe0 0xe1 0xe2 0xe3 0xe4 0xe5 0xe6 0xe7
Output8 source select key code:
0xf0 0xf1 0xf2 0xf3 0xf4 0xf5 0xf6 0xf7
12. Advanced Operation
Controlling the MX0606/0808-PP using RS232 and
COMCTL PC Software
Typically, unless alternative methods of controlling the matrix are
chosen or problems with device communication through the matrix
encountered, basic operation is all that is required to operate
your MX0606/0808-PP. However, the following information
on advanced operation will detail how the matrix system can be
configured and for advanced control and settings can be altered
or data manually input should such problems arise, as well as
configuring the system for third party control.
RS232 Remote Control
Control of the matrix is possible through RS232 using third party
control systems or the dedicated Wyrestorm COM CTL software
included with your purchase (also downloadable from www.
wyrestorm.com).
RS232 Setting
Should third party control be required, please see below for control
system configuration and hex code input. The RS232 connection
on the matrix is female QB9 Users can use a USB to RS232
cable or a direct male to female serial cable.
5
4
3
2
1
9
Ground
RXD TXD
8
7
6
Female connector - 9 holes
1
2
3
4
5
6
Ground
RXD
TXD
7
8
9
Male connector - 9 holes
RXD
Receive serial data from PC
TXD
Transmit serial data to PC
Baud rate
9600bps
Data bits
8bits
Parity None
Stop bits
1
Flow control
None
Com Port Setting
COM CTL
After fully connecting all inputs and outputs to the matrix and
installing the software, on opening the program the control
window will display information from the matrix, such as messages
received from the switch such as input/output details, firmware
version and control commands/HEX codes that allow the system
to be controlled remotely, as well as buttons used to navigate the
screen.
13
Technical Support: [email protected] US: +866 677 0053 EU: +44 (0) 1793 230 343
ADV
AN
CE
D R
E
M
O
TE CONTR
OL
11. Advanced Remote
Control
IR Call Back and Third Party Control systems
Please note:
Due to the differing method of control based on
location, if you are using a third party control system, learning the
control from the IR is NOT recommended as control will be limited
to scrolling up/down between inputs. For discrete source selection
you will need to import discrete hex codes for control systems.
These can be obtained through the Wyrestorm website, by
contacting our technical support or you can input them manually.
For reference:
The IR is NEC and possesses a carrier wave of
38KHz with a system code of 0x00
OUTPUT
CHANNEL
INPUT SELECT
1
2
3
4
5
6
7
8
0x1d 0x0d
0x1b 0x15
0x12 0x08
0x55 0x4a
0x06 0x03
0x07 0x02
0x44 0x51
0x1e 0x1a
Output1 source select key code:
0x80 0x81 0x82 0x83 0x84 0x85 0x86 0x87
Output2 source select key code:
0x90 0x91 0x92 0x93 0x94 0x95 0x96 0x97
Output3 source select key code:
0xa0 0xa1 0xa2 0xa3 0xa4 0xa5 0xa6 0xa7
Output4 source select key code:
0xb0 0xb1 0xb2 0xb3 0xb4 0xb5 0xb6 0xb7
Output5 source select key code:
0xc0 0xc1 0xc2 0xc3 0xc4 0xc5 0xc6 0xc7
Output6 source select key code:
0xd0 0xd1 0xd2 0xd3 0xd4 0xd5 0xd6 0xd7
Output7 source select key code:
0xe0 0xe1 0xe2 0xe3 0xe4 0xe5 0xe6 0xe7
Output8 source select key code:
0xf0 0xf1 0xf2 0xf3 0xf4 0xf5 0xf6 0xf7
12. Advanced Operation
Controlling the MX0606/0808-PP using RS232 and
COMCTL PC Software
Typically, unless alternative methods of controlling the matrix are
chosen or problems with device communication through the matrix
encountered, basic operation is all that is required to operate
your MX0606/0808-PP. However, the following information
on advanced operation will detail how the matrix system can be
configured and for advanced control and settings can be altered
or data manually input should such problems arise, as well as
configuring the system for third party control.
RS232 Remote Control
Control of the matrix is possible through RS232 using third party
control systems or the dedicated Wyrestorm COM CTL software
included with your purchase (also downloadable from www.
wyrestorm.com).
RS232 Setting
Should third party control be required, please see below for control
system configuration and hex code input. The RS232 connection
on the matrix is female QB9 Users can use a USB to RS232
cable or a direct male to female serial cable.
5
4
3
2
1
9
Ground
RXD TXD
8
7
6
Female connector - 9 holes
1
2
3
4
5
6
Ground
RXD
TXD
7
8
9
Male connector - 9 holes
RXD
Receive serial data from PC
TXD
Transmit serial data to PC
Baud rate
9600bps
Data bits
8bits
Parity None
Stop bits
1
Flow control
None
Com Port Setting
COM CTL
After fully connecting all inputs and outputs to the matrix and
installing the software, on opening the program the control
window will display information from the matrix, such as messages
received from the switch such as input/output details, firmware
version and control commands/HEX codes that allow the system
to be controlled remotely, as well as buttons used to navigate the
screen.
12. Advanced Operation
9 Pins
ADV
ANCED REMOTE CONTROL
Summary of Contents for HDBaseT Lite
Page 29: ...29 Technical Support support wyrestorm com US 866 677 0053 EU 44 0 1793 230 343 NOTES ...
Page 30: ...30 Technical Support support wyrestorm com US 866 677 0053 EU 44 0 1793 230 343 NOTES ...
Page 31: ...31 Technical Support support wyrestorm com US 866 677 0053 EU 44 0 1793 230 343 NOTES ...
