Vanco HDBaseT Lite, Instruction Manual

Page: 14 / 32

14
Technical Support: support@wyrestorm.com US: +866 677 0053 EU: +44 (0) 1793 230 343
A large yellow number denotes each OUTPUT section
with INPUTS chosen by either clicking the left/right arrow
buttons to scroll through inputs numerically or by pressing
the input numbers below.
The INPUT/OUTPUT switch allows output port selection
(display) and Input port select (source) buttons for specific
combinations of displays and sources within the matrix.
You can save your selections by allocating your choices
to Save buttons 1-3 and recall previously saved
output/ input configurations by pressing State 1-3
buttons.
Firmware Update
To update the system firmware, enter the following
code into the Send Message Window ensuring to
include one space between each section of the code.
Code: ICP BE 7C 5F
Press Enter , then Send Message to put the matrix
into firmware update mode.
Press the Disconnect button and run the firmware.
When the firmware has finished updating, press the same
button again to Connect and power-cyle the matrix
(turn off and on).
Updates are now active and the MX0606/0808-PP
firmware is now updated.
Control Command Format
Should users wish to write their own command software
for controlling the matrix remotely, see information on data
format and baud rate settings:
COM PORT Setting
Setting – Enter the Settings menu area to make
alternations to the matrix, IR, EDID etc. See below for
details.
SWITCH – Quick Switch option is an alternative
method of switching between sources that is faster than
in Normal mode, resulting in less delay between input
selection. Although faster, the means of switching has
been found to be incompatible with some displays. As
a result we recommend Normal Switch as the default
setting due to reliability and compatibility with outputs.
IR CALL-BACk – This toggles the IR Call-Back
function on and off. The default setting is ON
HDMI LONG CABLE MODE – If devices connected
using HDMI are reaching the upper end of the HDMI
transmission limit (15m / 49ft) and signal interference or
loss is experienced, switching Long Cable Mode to ON
15 Technical Support: support@wyrestorm.com US: +866 677 0053 EU: +44 (0) 1793 230 343
ADV
AN
CE
D OPE
RA
TI
ON
combinations of displays and sources within the matrix.You
can save your selections by allocating your choices to Save
buttons 1-3 and recall previously saved output/ input
configurations by pressing State 1-3 buttons
Firmware Update
To update the system firmware, enter the following code into
the
Send Message Window ensuring to include one
space between each section of the code.
Code:
1CP BE 7C 5F
Press
Enter
, then
Send Message
to put the matrix
into firmware update mode.
Press the
Disconnect
button and run the firmware.
When the firmware has finished updating, press the same
button again to
Connect
and powercyle the matrix
(turn off and on).
Updates are now active and the MX0606/0808-PP
firmware is now updated.
11
10
04
05
08
08
5 4 3 2 1
9
Ground
RXD TXD
8 7 6
Female connector - 9 holes
1 2 3 4 5
6
Ground
RXD TXD
7 8 9
Male connector - 9 holes
RXD Receive serial data from PC
TXD Transmit serial data to PC
Baud rate 9600bps
Data bits 8bits
Parity None
Stop bits 1
Flow control None
Com Port Setting
Control Command Format
Should users wish to write their own command software
for controlling the matrix remotely, see information on data
format and baud rate settings:
COM PORT Setting
13
Setting
– Enter the Settings menu area to make alternations
to the matrix, IR, EDID etc. See be-low for details.
01
MX0808-PP
MX0606-PP
03
04
02
05
06
08
07
01
SWITCH – Quick Switch option is an alternative method
of switching between sources that is faster than in Normal
mode, resulting in less delay between input selection.
Although faster, the means of switching has been found to be
incompatible with some displays. As a result we recommend
Normal Switch
as the default setting due to reliability and
compatibility with outputs.
02
IR CALL-BACK
– This toggles the IR Call-Back function on
and off. The default setting is ON
03
HDMI LONG CABLE MODE
– If devices connected using
HDMI are reaching the upper end of the HDMI transmission
limit (15m / 49ft) and signal interference or loss is
experienced, switching Long Cable Mode to ON will instruct
the matrix to attempt to aid transmission of the HDMI signal.
This setting is locked by default.
04
UTP LONG CABLE MODE
– As with HDMI Long Cable
Mode, if signal transmission quality is ef-fected by a
Cat5e/6/7 cable run reaching the maximum distance
capacity (70m / 230ft using RX-1UTP-IR-70), switching
Long Cable Mode to ON will instruct the matrix to attempt
to improve transmission over the UTP in an effort to improve
signal quality.
This mode should NOT be used as a general means to
lengthen transmission distance – we recommend in-stallers
be aware of product specifications and use equipment best
suiting the requirements of the project. This setting is locked
by default.
4
5
8
8
10
11
13
1
1
5
2
2
6
3
3
7
4
8
MX-0606-PP
MX-0808-PP
ADV
ANCED OPERA
TION