Vanco HDBaseT Lite, Instruction Manual

Page: 10 / 32

10
Technical Support: support@wyrestorm.com US: +866 677 0053 EU: +44 (0) 1793 230 343
IR Call-back of Matrix and Source Devices
The Wyrestorm MX0606/0808-PP is not only a switcher
and extender of multiple HDMI signals to multiple HDMI
receivers located remotely, it also passes IR control
signals through the IR call-back system to the matrix
and HDMI sources for full, independent control of all
connected inputs from output locations.
Two-way IR Call-back Between Matrix, Sources and
Displays from Multiple Locations
A key feature on our HDBaseT Lite Matrix range is
discrete IR control of the matrix, sources and displays
from any location – so inputs at the matrix end can be
controlled at a display location and displays can be
controlled at the matrix location.
This is accomplished by placing a series of IR Emitters on
devices to control and Receivers at all locations you wish
to control from to enable the IR signal to travel both ways
via the single Cat5e/6/7 cable.
The sequence of IR TX numbers correspond to the HDMI
INPUTS so when an OUTPUT selects a certain INPUT,
the CALL-BACK IR signal of that RJ45 port selects the
relevant IR TX port to OUTPUT the control signal.
Example: If OUTPUT 1 selects INPUT 3, the CALL-BACK
IR signal of that RJ45 OUTPUT links INPUT 3 with IR TX3
for the signal to be combined and communicated for that
input to be controlled remotely.
At Matrix end: Insert the 3.5mm jacks of the IR TX
Emitters included with the unit into the IR TX Emitter ports
at the rear of the matrix according to input. The IR signal
is added to the HDMI of the input device so, for example,
if the user is watching Blu-ray on input 3, the IR signal
will be directed through the IR TX3 socket to control the
device.
BASIC REMOTE CONTROL
11 Technical Support: support@wyrestorm.com US: +866 677 0053 EU: +44 (0) 1793 230 343
B
AS
IC R
E
M
O
TE CONTR
OL
IR Call-back of Matrix and Source Devices
The Wyrestorm MX0606/0808-PP is not only a switcher and
extender of multiple HDMI signals to multiple HDMI receivers
located remotely, it also passes IR control signals through the
IR call-back system
to the matrix and HDMI sources for full,
independent control of all connected inputs from output locations.
Two-way IR Call-back Between Matrix, Sources and
Displays from Multiple Locations
A key feature on our HDBaseT Lite Matrix range is discrete IR
control of the matrix, sources and displays from any location – so
inputs at the matrix end can be controlled at a display location and
displays can be controlled at the matrix location.
This is accomplished by placing a series of IR Emitters on devices
to control and Receivers at all locations you wish to control from to
enable the IR signal to travel both ways via the single Cat5e/6/7
cable.
The sequence of IR TX numbers correspond to the HDMI INPUTS
so when an OUTPUT selects a certain INPUT, the CALL-BACK
IR signal of that RJ45 port selects the relevant IR TX port to
OUTPUT the control signal.
Example: If OUTPUT 1 selects INPUT 3, the CALL-BACK IR
signal of that RJ45 OUTPUT links INPUT 3 with IR TX3 for the
signal to be combined and communicated for that input to be
controlled remotely.
IR Path
IR Path
IR Path
IR Receiver
1 2 3 4
1
1 2 3 4
2
1 2 3 4
3
1 2 3 4
4
HDBT OUT 1
HDBT OUT 2
HDBT OUT 3
HDBT OUT 4 HDBT OUT 5
HDBT OUT 6
HDBT OUT 7
HDBT OUT 8
Single Cat5e/6/7
70m/230ft
Display
Reciever
HDMI Source
HDMI Cable
IR TX Receiver
IR RX Receiver
Cat5e/6/7 up to
70m (230ft)
HDMI Input 1
IR TX 1
HDMI Input 2
IR TX 2
HDMI Input 3
IR TX 3
HDMI Input 4
IR TX 4
HDMI Input 5
IR TX 1
HDMI Input 6
IR TX 2
HDMI Input 7
IR TX 3
HDMI Input 8
IR TX 4
IR RX Receiver
IR TX Emitter
1 2 3 4
1
1 2 3 4
2
1 2 3 4
3
1 2 3 4
4
IR Path
IR Path
IR Path
UTP Out 1
UTP Out 2
UTP Out 3
UTP Out 4
UTP Out 5
UTP Out 6
UTP Out 7
UTP Out 8
1 2 3 4
1
1 2 3 4
2
1 2 3 4
3
1 2 3 4
4
01
02
01
At Matrix end:
Insert the 3.5mm jacks of the IR TX Emitters
included with the unit into the IR TX Emitter ports at the
rear of the matrix according to input. The IR signal is added
to the HDMI of the input device so, for example, if the user
is watching Blu-ray on input 3, the IR signal will be directed
through the IR TX3 socket to control the device. As each
11
Technical Support: support@wyrestorm.com US: +866 677 0053 EU: +44 (0) 1793 230 343
B
AS
IC R
E
M
O
TE CONTR
OL
IR Call-back of Matrix and Source Devices
The Wyrestorm MX0606/0808-PP is not only a switcher and
extender of multiple HDMI signals to multiple HDMI receivers
located remotely, it also passes IR control signals through the
IR call-back system
to the matrix and HDMI sources for full,
independent control of all connected inputs from output locations.
Two-way IR Call-back Between Matrix, Sources and
Displays from Multiple Locations
A key feature on our HDBaseT Lite Matrix range is discrete IR
control of the matrix, sources and displays from any location – so
inputs at the matrix end can be controlled at a display location and
displays can be controlled at the matrix location.
This is accomplished by placing a series of IR Emitters on devices
to control and Receivers at all locations you wish to control from to
enable the IR signal to travel both ways via the single Cat5e/6/7
cable.
The sequence of IR TX numbers correspond to the HDMI INPUTS
so when an OUTPUT selects a certain INPUT, the CALL-BACK
IR signal of that RJ45 port selects the relevant IR TX port to
OUTPUT the control signal.
Example: If OUTPUT 1 selects INPUT 3, the CALL-BACK IR
signal of that RJ45 OUTPUT links INPUT 3 with IR TX3 for the
signal to be combined and communicated for that input to be
controlled remotely.
IR Path
IR Path
IR Path
IR Receiver
1 2 3 4
1
1 2 3 4
2
1 2 3 4
3
1 2 3 4
4
HDBT OUT 1
HDBT OUT 2
HDBT OUT 3
HDBT OUT 4 HDBT OUT 5
HDBT OUT 6
HDBT OUT 7
HDBT OUT 8
Single Cat5e/6/7
70m/230ft
Display
Reciever
HDMI Source
HDMI Cable
IR TX Receiver
IR RX Receiver
Cat5e/6/7 up to
70m (230ft)
HDMI Input 1
IR TX 1
HDMI Input 2
IR TX 2
HDMI Input 3
IR TX 3
HDMI Input 4
IR TX 4
HDMI Input 5
IR TX 1
HDMI Input 6
IR TX 2
HDMI Input 7
IR TX 3
HDMI Input 8
IR TX 4
IR RX Receiver
IR TX Emitter
1 2 3 4
1
1 2 3 4
2
1 2 3 4
3
1 2 3 4
4
IR Path
IR Path
IR Path
UTP Out 1
UTP Out 2
UTP Out 3
UTP Out 4
UTP Out 5
UTP Out 6
UTP Out 7
UTP Out 8
1 2 3 4
1
1 2 3 4
2
1 2 3 4
3
1 2 3 4
4
01
02
01
At Matrix end:
Insert the 3.5mm jacks of the IR TX Emitters
included with the unit into the IR TX Emitter ports at the
rear of the matrix according to input. The IR signal is added
to the HDMI of the input device so, for example, if the user
is watching Blu-ray on input 3, the IR signal will be directed
through the IR TX3 socket to control the device. As each
1
1
2