Valley-Dynamo Jet-Pong Coin JP100 User Manual Download Page 3

Page: 3 / 80

Jet-Pong Coin JP100 User’s Manual

Preface

All rights reserved. No Part of this work covered by the copyright hereon may be reproduced or used in any form
or by any means

—graphic, electronic, or mechanical, including photocopying, recording, taping, music, video,

software or information storage and retrieval systems without express written permission of Valley-Dynamo and
Aerr Technologies.

Jet-Pong

is a registered trademark. Reg. No.

5,962,669 and 1,925,931

United States Patent

# 7,673,877 B2

Canada Patent

# 2,566,249

United States Patent Filing

# 63/190,372

Jet-Pong Coin JP100

User’s Manual

Document Revision

– 1.0 Date – 09/18/2021

Dear Customer,

Thank you for choosing a quality engineered Valley-Dynamo product. Jet-Pong has been built with
comprehensive quality assurance to ensure your satisfaction and trouble free use of the product.

This manual was written to assist you with Set-Up, Operation, Maintenance & Troubleshooting. Below is a list of
sales and technical support contacts.

Special thanks to Aerr-Technologies for developing the technology and to Voyager, a Canadian band for
developing much of the music.

We sincerely hope that you and your customers will enjoy playing Jet-Pong.

Valley-Dynamo

www.valley-dynamo.com

7115 Belton St.

Richland Hills, TX 76118

U.S.A.

National Sales Email:

[email protected]

International Sales Email:

[email protected]

Technical Assistance:

[email protected]

Tech Support Hotline

(during business hours Central U.S. Time):

1-972-595-5300

(follow prompts for Tech

Support)

Spare Parts:

www.valley-dynamoparts.com

An Electronic Version of this manual can be found at:

www.valley-dynamoparts.com

Summary of Contents for Jet-Pong Coin JP100

















































































Search results

Summary of Contents for Jet-Pong Coin JP100

Reviews:

Related manuals for Jet-Pong Coin JP100

Brands by name

Popular brands

Valley-Dynamo Jet-Pong Coin JP100, User Manual

Search results

Summary of Contents for Jet-Pong Coin JP100

Reviews:

Related manuals for Jet-Pong Coin JP100

Brands by name

Popular brands