VALERA SWISS'X 100 Series, Operating Instructions Manual

Page: 4 / 86

8
from the power supply socket. Do not pull on the wire to
remove the plug from the power supply socket. Do not
pull the plug out of the power supply socket when your
hands are wet.
• Always allow the unit to cool before putting it away and
never wrap the cord around the unit.
• Check that the cord has not been damaged from time to
time.
• Prevent the cord from coming into contact with the metal
parts while these are still hot.
• Use the unit on dry hair.
• Do not use this unit on wigs that have synthetic hair.
• The elements used to pack the unit (plastic bags,
cardboard box, etc.) must be kept out of reach of children
as they are a potential danger to them.
• This unit must only be used for the purposes for which it
is expressly intended. Any other use is to be considered
improper and therefore dangerous. The manufacturer
accepts no responsibility for damage caused by improper
or erroneous use.
• Do not use hair spray while the unit is running.
• Keep the plates clean and free of dust, hair spray, styling
gel, etc.
• To avoid dangerous overheating, it is advisable to unwind
the entire length of the cord.
• The A-weighted sound pressure level of the hair
straighteners for professional use is below 70 dB(A).
• Designation of the appliance (see technical product
specifications)
HAND-HELD HAIR STRAIGHTENER FOR PROFESSIONAL
USE
OPERATING INSTRUCTIONS
PARTS
1. Appliance
2. Straightening plates
3. ON-OFF switch
4. Temperature adjustment controls
(Type 100.20/IS,
100.20/I, 100.20, 100.30/IS, 100.30/I, 100.30, 100.11/IS,
100.11/I, 100.11)
5. Temperature selector
(Type 100.02/I, 100.02, 100.05/I,
100.05)
6. Indicator light
(Type 100.02/I, 100.02, 100.05/I, 100.05)
7. Display
(Type 100.20/IS, 100.20/I, 100.20, 100.30/IS,
100.30/I, 100.30, 100.11/IS, 100.11/I, 100.11, )
8. X’Brush accessory
(for models supplied with this
accessory
9. Thermocap accessory
10. Heat-resistant carry pouch
(for models supplied with this
accessory)
Fig. 8.
Switching the appliance
on and off
Type 100.20/IS, 100.20/I, 100.20, 100.30/IS,
100.30/I, 100.30, 100.11/IS, 100.11/I, 100.11,
100.02/I, 100.02, 100.05/I, 100.05
To switch the appliance on, simply plug it in to an electrical
socket, then press and hold the ON-OFF switch (fig. 1, ref. 3)
for one second. To switch it off, press and hold the ON-OFF
button (fig. 1, ref. 3) for 3 seconds again and remove the plug
from the socket.
°C °F
Temperature settings
Type 100.20/IS, 100.20/I, 100.20, 100.30/IS,
100.30/I, 100.30, 100.11/IS, 100.11/I, 100.11
To select the operating temperature, switch on the appliance
and press the “+” or “-” control (fig. 1, ref. 4) until the display
(fig. 1, ref. 7) shows the desired temperature.
Different temperatures may be selected for different hair types
at intervals of 10°C, from a minimum of 120°C to a maximum
of 230°C.
After the selected value has been blinking for a few seconds,
the display (fig. 1, ref. 7) will show the actual temperature of
the straightening plates (fig. 1, ref. 2). When the temperature
of the straightening plates is lower than 110°, 3 dashes flash
on the display.
Wait for the selected temperature to be reached, then begin
styling the hair.
Type 100.02/I, 100.02, 100.05/I, 100.05
Select the desired temperature using the corresponding wheel
(fig. 1, ref. 5): when the LED (fig. 1, ref. 6) stops blinking, the
appliance is ready to use.
AUTOMATIC DEACTIVATION
OF SAFETY
and “HOT” FUNCTION
The appliance automatically switches off 60 minutes after it
was switched on:
- in 100.20/IS, 100.20/I, 100.20, 100.30/IS, 100.30/I,
100.30, 100.11/IS, 100.11/I, 100.11 models, 5 minutes
before automatic deactivation, the display (fig. 1, ref. 7)
shows the temperature and the text “off” alternately.
When 60 minutes have elapsed, if the power button (fig. 1, ref.
3) has not been pressed again, the straightening plates (fig. 1,
00060754 int_gen2018_Layout 1 22/01/2018 12:49 Pagina 8