manualshive.com logo in svg

Vaisala AWS310-SITE, Configuration And Maintenance Manual

Share
Download
Vaisala AWS310-SITE Configuration And Maintenance Manual Download Page 92

When the status LED turns red, QBR101C disconnects the load at the DCout/Switch
terminal, and shuts down the system. This protects the batteries from deep discharging.

1. Disconnect the AC (mains) power supply or the external DC.

2. To see the battery status, press the QBR101C 

TEST

 button: 

• If the LED is green, the battery is OK.
• If the LED is yellow, the battery voltage is low (level < 11.5 V).
• If the LED is red, the battery is empty (level < 10 V).

3. Charge the battery for a while. Then, repeat the procedure from 

step 1

. 

5.6.4 Replacing 12 V / 26 Ah Battery

• Allen keys
• Slothead screwdriver

Only licensed experts may install electrical components. They must

adhere to local and state legislation and regulations.

WARNING!

Do not replace the battery with a battery of an incorrect type. If you do,

there is a risk of explosion. Dispose of used batteries according to statutory regulations.

WARNING!

The expected lifetime for the backup battery is 5 years.

The backup battery does not have any replaceable parts.

1. Switch off the battery fuse. 

If the AC (mains) power is connected and viable, the weather station continues to
operate normally during the battery change.

AWS310-SITE Configuration and Maintenance Manual

M211828EN-C

90

Summary of Contents for AWS310-SITE

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands