VADDIO RoboTRAK Integrator'S Complete Manual Download

Page: 60 / 74

streaming settings

Retrieves or specifies the IP streaming settings for the camera.

Synopsis

streaming settings {get | set [ip_enabled] | [ip_port] | [ip_protocol] | [ip_
quality] | [ip_resolution] | [ip_url]}

Options

ip_enabled

[true |

false]

true

enables streaming;

false

disables it.

ip_port

<port

number>

Specifies the port that the IP stream uses. Port
554 is the default.

ip_protocol

[rtsp] Specifies the streaming protocol. Only RTSP is

supported at this time.

ip_quality

[low |

standard | high]

Specifies the video quality. Low is useful for low-
bandwidth situations.

ip_resolution

<480p>

Specifies streaming video resolution. For the
RoboTRAK IR camera, 480p is the only valid
streaming resolution.

ip_url

<URL>

Specifies the URL where the stream is
available.

Examples

> streaming settings get

IP Enabled

true

IP Port

554

IP Protocol

RTSP

IP Quality

High Quality (Best)

IP Resolution

480p

IP URL

vaddio-robotrak-stream

> OK

system reboot

Reboots the system either immediately or after the specified delay. Note that a reboot is required when
resetting the system to factory defaults (system factory-reset).

Synopsis

system reboot [<seconds>]

Options

The number of seconds to delay the
reboot

Examples

system reboot

Reboots the system immediately.

system reboot 30

Reboots the system in 30 seconds.

Integrator's Complete Guide to the RoboTRAK Presenter Tracking System

Summary of Contents for RoboTRAK











































































Search results

Summary of Contents for RoboTRAK

Reviews:

Related manuals for RoboTRAK

Brands by name

Popular brands

VADDIO RoboTRAK, Integrator'S Complete Manual

Search results

Summary of Contents for RoboTRAK

Reviews:

Related manuals for RoboTRAK

Brands by name

Popular brands