UTE X2-3232 User Manual Download Page 29

Page: 29 / 84

X2-3232: Modular Matrix Switcher 32x32

U.T.E. electronic GmbH & Co. KG

www.ute.de

2.3.6.2. X2-4O-UFS: 1080P seamless OPTICAL output card

1080P seamless OPTICAL output card with 4 OPTICAL ports.

X2-4O-UFS

⚫

Supports seamless switching, it can be used in combination with other seamless
input signal card.

⚫

Supports output resolution selection, and it is up to 1920x1080P@60Hz.

⚫

It is used with optical fiber receiver to extend video signal, and the transmission
distance can up to 2 kilometers by single-mode optical fiber cable, or 300 meters by
multi-mode optical fiber cable.

⚫

The input signal cannot be transmitted with HDCP.

⚫

The input card does not support DDC channel.



Note:

Before using the X2-4I-UFS and X2-4O-UFS, the firmware program of matrix

front-board and back-board needs to be upgraded. Please seek technical
assistance from our technical support.

Summary of Contents for X2-3232




















































































Search results

Summary of Contents for X2-3232

Reviews:

Brands by name

Popular brands

UTE X2-3232, User Manual

Search results

Summary of Contents for X2-3232

Reviews:

Brands by name

Popular brands