Urrea SI810 User Manual And Warranty Download Page 25

25

E N G L I S H •

User’s manual

either right or left, depending on the desired 
cut for the application. See the chart below for 
correct angle settings and correct positioning 
of crown molding on miter table.
The settings in the chart below can be used 
for cutting All Standard (U.S.) crown molding 
with 52° and 38° angles. The crown molding is 
placed flat on the miter table using the com-
pound features of the miter saw.

CUTTING WARPED MATERIAL
When cutting warped material, always make 
sure it is positioned on the miter table with the 
convex side against the fence.
If the warped material is positioned the wrong 
way, it will pinch the blade near the comple-
tion of the cut.

 WARNING: To avoid a kickback and to 

avoid serious personal injury, never position 
the concave edge of bowed or warped mate-
rial against the fence.

CLAMPING WIDE WORKPIECES
When cutting wide workpieces, such as 2" x 6", 
boards should be clamped with a C-clamp.

38

°

52

°

CEILING

FENCE

FENCE

MITER 

TABLE

MITER 

TABLE

INSIDE 

CORNER

OUTSIDE 

CORNER

TOP EDGE AGAINST FENCE =

• LEFT SIDE, INSIDE CORNER

• RIGHT SIDE, OUTSIDE   

   CORNER

BOTTOM EDGE AGAINST FENCE= 

• RIGHT SIDE, INSIDE CORNER

• LEFT SIDE, OUTSIDE CORNER

W

ALL

RIGHT

WRONG

Left side, inside corner

1. Top edge of molding against fence.

2. Miter table set right 31.62°

3. Save left end of cut.
Right side, inside corner

1. Bottom edge of molding against fence.

2. Miter table set left 31.62°

3. Save left end of cut.
Left side, outside corner

1. Bottom edge of molding against fence.

2. Miter table set left 31.62°

3. Save right end of cut.
Right side, outside corner

1. Top edge of molding against fence.

2. Miter table set right 31.62°

3. Save right end of cut.

Type of Cut

Bevel

Angle

Setting

33.85˚

33.85˚

33.85˚

33.85˚

SI810 manual.indd   25

08/12/15   2:54 p.m.

Summary of Contents for SI810





























Reviews: