Urrea SI810 User Manual And Warranty Download Page 22

22

If your saw does not have extension wings, use 
a support that is the same height as the table. 
The support must allow the workpiece to lay 
flat against the table, it must be very stable, 
and it must not move with the workpiece.

USING CARBIDE-TIPPED BLADES

 WARNING: Read, understand and follow all 

warnings and instructions provided with your 
carbide-tipped blades.

Handle carbide-tipped blades carefully. Car-
bide is very brittle and can be easily damaged. 
Use caution when you install, use and store 
your blades. Do not use a carbide-tipped blade 
that is bent or has bent teeth, or if the blade 
has cracks, broken, missing or loose carbide 
tips. Do not operate a carbide-tipped blade 
faster than its maximum recommended speed.

CHANGING YOUR SAW BLADE

 WARNINGS: 

• Before changing your saw blade, unplug 
the power cord from the Electrical outlet. The 
power cord must remain unplugged whenever
You are working on your saw.
• To avoid injury from a thrown workpiece, do 
not use a blade larger Or smaller than 10" (25.4 
cm).
• Do not use a dull saw blade. Additional force 
is required to operate making it unsafe.

Immediately replace the saw blade if it shows 
signs of deterioration or damage. Dull or dam-
aged saw blades can cause personal injury and 
ineffective operation of your saw.

 WARNING: Do not cut ferrous metals with 

this machine. This miter saw is not warrantied 
if used for cutting ferrous metals.

 WARNING: To avoid injury, follow all ap-

plicable safety instructions, when cutting non-
ferrous metals:
• Use only saw blades specifically recommend-
ed for non-ferrous metal cutting.
• Do not cut metal workpieces that must be 
hand held. Clamp workpieces securely.
• Cut non-ferrous metals only if you are under 
the supervision of an experienced person.

1. Loosen the guard 
plate screw (1) (Fig. 
13).
2. Rotate the lower 
blade guard up to ex-
pose the arbor screw 
(2) (Fig. 14).
3. While pushing in on 
the arbor lock (3) to 
hold the blade in po-
sition, turn the arbor 
screw clockwise using 
the socket wrench 
supplied with your 
saw (Figs. 15 and 16).

NOTE: Turn the arbor screw clockwise to loosen
and counter-clockwise to tighten. 
4. Remove the arbor screw, washer, outer blade
collar and blade. Do not remove the inner 
blade collar.
5. Clean any sawdust from both blade collars 
before installing the blade. Install a 10" (25.4 
cm) blade only. Verify the rotation arrow on 
the blade matches the cast-in rotation arrow 
on the upper blade guard. Make sure the blade 
is behind the flange.
6. Install the outer 
blade collar (4), wash-
er (5) and arbor screw 
(6). While pushing 
in on the arbor lock, 
turn the arbor screw 
counter-clockwise to 
tighten (Fig. 17).
7. Rotate lower blade guard and guard plate 
down until the plate is behind the forward 
plate screw. Tighten both guard plate screws.
8. Slightly raise the lower guard plate until the 
screw and bushing can be threaded into the 
brass nut. Tighten the screw and make sure the 
bushing is centred in lever slot.

Fig.13

Fig.14

Fig.15

Fig.16

1

2

3

Fig.17

4

5

6

SI810 manual.indd   22

08/12/15   2:54 p.m.

Summary of Contents for SI810





























Reviews: