Urrea SI810 User Manual And Warranty Download Page 20

20

2. Tilt the saw back to gain access to the under-
side of the base. Secure the saw so that it will 
not tip or fall off the workbench.
3. Slide the stop bracket (1) onto the rear rail 
of one of the extension wings (2). Secure the 
wing screw (3) that holds the stop bracket in 
place.
4. Insert both rails of an extension wing 
through the first set of holes (4) on the outside 
of the saw base.
5. Place a bar holder clamp (5) over each rail.
6. Slide the rails through the second set of 
holes (6) until the rails rest against the base of 
the saw (7). Make sure the bar holder clamps 
rest against the outside wall (10) of the saw 
base.

7. Tighten the screws (8) that secure the bar 
holder clamps to the rails. Make sure the ex-
tension wings do not move and turn the lock 
nuts (9) clockwise to prevent the screw from 
loosening.
8. Repeat steps 4 through 7 to install an exten-
sion wing on the other side of the saw.
9. Place the saw in the upright position on the 
workbench.

ADJUSTMENTS

 WARNING: Before performing any adjust-

ments to your saw, unplug the power cord 
from electrical outlet. the power cord must 
remain unplugged whenever you are working 
on your saw.

NOTE: VERIFY THE FOLLOWING ADJUSTMENTS 
TO ENSURE CUTTING ACCURACY.
BLADE-TO-FENCE ADJUSTMENT (Fig.5)
Make sure the blade is square to the fence.

1. Lock the handle in 
the down position. 
Hold a combination 
square (1) against the 
fence (2) and next to 
the blade (3). 

Avoid touching the saw teeth with the square. 
The set in the blade’s teeth will hold the square 
away from the blade. The blade should contact 
the full length of the square.
2. If the blade does not contact the full length 
of the square, adjust the fence as follows.
3. Loosen the four fence adjustment screws (4) 
using a 9/16" (14 mm) socket or wrench.
4. Hold the square against the blade. Move the 
fence until it contacts the full length of the 
square.
5. Tighten the fence adjustment screws.
NOTE: The combination square and the wrench 
shown are not provided.

BASE-TO-BLADE ADJUSTMENT (Fig. 6,7 & 8)
Make sure the blade is perpendicular to the 
base.
1. While lowering the 
blade, hold a com-
bination square (1) 
against the base (2) 
and next to the blade 
(3). Avoid touching 
the saw teeth with the 
square. The set in the 
blade’s teeth will hold 
the square away from 
the blade. The blade 
should contact the full 
length of the square.
2. If the blade does 
not contact the full 
length of the square, 
adjust the bevel ad-
justment screw as fol-
lows. 
3. Loosen the bevel 
adjustment screw 
(4). Hold the square 
against the base. 
Rotate the bevel ad-
justment screw, up or 
down, until the full 
length of the square is 
against the blade.
4. Tighten the bevel adjustment screw.
5. Make sure the bevel indicator is aligned with 
the bevel index 0° mark. If adjustment if neces-
sary, loosen the bevel indicator screw (5) and 
move it to align with the 0° mark. Tighten the 
bevel indicator screw.

1

2

3

9

8

10

4

5

6

7

Fig.3

Fig.4

Fig.6

1

2

3

Fig.5

4

45

30

225

15

1

2

3

Fig.7

4

Fig.8

5

SI810 manual.indd   20

08/12/15   2:54 p.m.

Summary of Contents for SI810





























Reviews: