17
E N G L I S H •
User's Manual
DECORATIVE CUT
To make a decora-
tive cut around trees,
posts, fences, etc., turn
the whole unit so that
the cutting head is at
an angle of 30 ° to the
ground.
BORDERING
During cutting at the
edges and lowering
hold the unit at a steep
angle and in a position
where debris, dirt and
the stones that come off, do not come back to
you, even if it bounces on the hard surface. Al-
though the image shows how to skirt and make
the recess of the grass, each operator must find
by himself the angles that adapt to the size of his
body and the cutting situation.
BLADE CUTTING
There are many types of blades, the most com-
monly used are the following.
The 3/4 “diameter cut-
ting blade is used to cut
weeds and weeds. Only
the blade of 255 mm of
3 blades can be used in
this type of trimmer.
WARNING: do not use the cutting blades to
cut trees.
WARNING: do not use a steel blade to edge
or scrape.
WARNING: do not cut with dull, cracked or
damaged blades. Before cutting tall grass, in-
spect the area for obstructions such as stones,
metal stakes or broken fence wire. If an obstruc-
tion can not be removed, mark your location
so you can avoid it with the blade. Rocks and
metal will wear or damage the blade. The cables
can snag on the head of the blade and flap or
launch into the air.
KICKBACK: the blade thrust is the reaction that
can occur when the blade (while it is running)
contacting something that can not be cut. This
contact can cause the blade to stop for a mo-
ment and, suddenly, “push” the machine away
from the struck object, enough for the operator
to lose control of the trimmer. Kickback of the
blade can occur without warning if the blade is
caught or jammed. This is more likely to occur in
areas where it is difficult to see the material be-
ing cut. To cut safely, get close to the weeds that
will be cut from right to left, in case it is the case
that an unexpected object or dangerous mate-
rial is found; this could minimize the backlash
reaction of the blade.
WARNING: IN CASE OF EXCESSIVE VIBRA-
TION - STOP THE ENGINE IMMEDIATELY.
Excessive vibration of the blade means that it is
not installed correctly. Stop the engine immedi-
ately and check the blade.
Incorrectly installed sheet will cause injuries.
WARNING: the cutting area is dangerous
while the machine is stopping.
NOTE: NOISE AND VIBRATION.
1. Low speed operation can reduce noise and
tremor.
2. To reduce noise, the brush cutter should be
used in an open environment.
3. The vibration can be reduced if the handle is
held firmly.
4. To avoid disturbing others, the machine must
be operated during the day.
5. Wear personal protective equipment, such as
gloves and ear protection during operation.
6. The machine is not for professional work and
is not for a prolonged operation.
7. To maintain the physical condition of the user
and prolong the life of the machine, do not
work more than 2 hours in a whole day and do
not continue working more than 10 minutes at
a time.
WARNING: the engine exhaust of this prod-
uct contains chemicals known to cause cancer,
birth defects or other reproductive harm.
MAINTENANCE
IMPORTANT:
BEFORE USING THE MACHINE,
PERFORM MAINTENANCE OR CHANGE OF AC-
CESSORY, READ THE “PERIODIC MAINTENANCE
TABLE” ON PAGE 20.
WARNING: use only original manufacturer’s
replacement parts, accessories and attachments.
Failure to do so can cause possible injury, poor
performance and may void your warranty.
REPLACING THE NYLON THREAD
1. Insert the hex key (2) into the specific hole
in the drive angle (3) and turn the key seal (4)
by hand until the hex key enters the inner hole,
blocking the rotation.
2. Make sure that the slots in the key seal (4) fit
perfectly with the transmission angle (3).
