Upswung Sentry Swing Installation And Maintenance Manual Download Page 4

Page: 4 / 50

This manual and its contents are based on the instructions written by FAAC-USA

Read all Instructions first BEFORE attempting

any Installation!

SECTION:

1. Review of specifications, warnings, parts, and tools

Specifications of the Sentry Swing and
Components

1.1

System Overview & Preliminary Checks

1.2

Sentry Swing Parts List

1.3

Tools Needed for Installation

1.4

2. Pre-installation charging

Control Board Layout

2.1

IMPORTANT: Charging Battery Prior to Use

2.2-.3

3. Basic Installation

IMPORTANT: 5” x 5” Setback

3.1

Installation of Mounting Hardware and Arm

3.2-.6

4. Mounting Control Box

Finding Location and Mounting

4.1

5. Pre-Learning Connections

Removable Terminal Strip

5.1

Installing temporary safety jumpers

5.2

Actuator Arm and Dual Power Connections

5.3

Installing the Receiver and Transmitter

5.4

Power

5.5

6. Basic Programming

Programming Gate Movement Variables

6.1

i.e. auto close, speed, force, delays

Gate Movement Variables LED Chart

6.2

One Touch

Programming

6.3-.4

Summary of Contents for Sentry Swing



















































Search results

Summary of Contents for Sentry Swing

Reviews:

Upswung Sentry Swing, Installation And Maintenance Manual, Page: 4 / 50

Search results

Summary of Contents for Sentry Swing

Reviews: