manualshive.com logo in svg

Upswung Sentry Swing, Installation And Maintenance Manual, Page: 3 / 50

Share
Download
Upswung Sentry Swing Installation And Maintenance Manual Download Page 3

Sentry Swing Summary

The Sentry Swing is only to be used for vehicular swing gates in a Class I setting.

Class I:

A vehicular gate opener (or system) intended for use in a home of one-to-four

single family dwelling, or a garage or parking area associated therewith.

The FAAC Sentry Swing automated system was designed and built for controlling vehicle
access. Do not use for any other purpose. The Sentry Swing automated system automates
residential swing-leaf gates with leaves of up to 12’ in length. It consists of a locking electro-
mechanical linear operator, powered by a 12V DC battery, coupled with control board recharging
the battery. The SLAVE equipment (required on 2-leaf gates only) is controlled by the MASTER
equipment to which all accessories and pulse generators are connected. The MASTER card
can be programmed and is used to set the following: function logics, work times (by self-
learning) and pause times, leaf speed, and the sensitivity of the anti-crushing de-vice.
The locking screw drive system will automatically lock when the motor is not operating. A
release system enables the gate to be moved by hand in case of a system failure.

Summary of Contents for Sentry Swing



















































Reviews:

No comments