manualshive.com logo in svg

Upswung Sentry Swing, Installation And Maintenance Manual, Page: 10 / 50

Share
Download
Upswung Sentry Swing Installation And Maintenance Manual Download Page 10

Control Board Wiring

Warning !!: Study the control board and read this section
thoroughly before attempting to operate your gate opener.

Warnings:

Before attempting any job on the control board (connections,
maintenance), turn off electrical power and unplug the support battery.

Install a surge protector upstream of your opener, the opener is not power
surge proof nor will power surge damage be covered under warrantee.

Always separate power from control and safety cables (push-buttons,
receivers, photocells, etc.). To avoid any electrical noise, use separate
sheaths or a shielded cable (with earthed shield).

LED

P

P 1
P 2
F 1
J 1
J 2
J 3
J 4
J 5

Programming LEDs

Power ON and diagnostics LED
“Function” programming push-
button “Value” programming
push-button Battery and motor
fuse - F15A Accessories
Terminal board

Transformer Terminal board
Motor connection terminal
Battery connector
Minidec connector/RP receiver

P
F 1
J 2
J 3

Power ON and diagnostic LED Battery
and motor fuse - F15A Bus connection
terminal board Motor connection terminal
board Battery connector

Summary of Contents for Sentry Swing



















































Reviews:

No comments