Upright ab62 Service And Parts Manual Download | Manualshive

Page: 48 / 146

background image

4-6

AB62 Work Platform - European

T

ROUBLESHOOTING

Section

4.2

LEDs on DMR-30 illuminated:
BT7-04 (cage rotate left output), BT5-06 (throttle out-
put), BT6-12 (low flow valve output).

Cage Trim Up

Function enabled - foot switch depressed.
LEDs on DMT-30 illuminated:
BT4-03 (foot pedal), BT4-11 (cage trim up).
LEDs on DMR-30 illuminated:
BT6-05 (cage trim up output), BT5-06 (throttle out-
put), BT6-12 (low flow valve output).

Cage Trim Down

Function enabled - foot switch depressed.
LEDs on DMT-30 illuminated:
BT4-03 (foot pedal), BT4-06 (cage trim down).
LEDs on DMR-30 illuminated:
BT6-06 (cage trim down valve), BT5-06 (throttle out-
put), BT6-12 (low flow valve output).

Auxiliary Power (Emergency Functions)

DMT-30 BT3-08 (auxiliary power)
DMR-30 BT5-10 (auxiliary output)

NOTE: If the auxiliary switch is depressed when

the engine is running, the engine will stop
immediately.

Drive Functions

Drive functions are relayed to the drive pump from
the joystick control. All adjustments are made at the
joystick controller. Brake release and throttle com-
mands are relayed from the joystick controller to the
DMT-30 on BT3-08 (JSA) Joystick actuator.

Drive Forward

Function enabled - footswitch depressed.
BT3-02 on DMT-30 (jsa) joystick actuator, BT5-06 on
DMR-30 (throttle output), BT5-04 (brake release).

Drive Reverse

Function enabled - footswitch depressed.
BT3-02 on DMT-30 (jsa) joystick actuator, BT5-06 on
DMR-30 (throttle output), BT5-04 (brake release).

Steer Right

Function enabled - foot switch depressed.
BT4-05 on DMT-30 (steer right), BT5-06 on DMR-30
(throttle output), BT6-10 on DMR-30 (high flow
valve), BT7-02 on DMR-30 (steer right output).

Steer Left

Function enabled - foot switch depressed.
BT4-10 on DMT-30 (steer left) BT5-06 on DMR-30
(throttle output) BT6-10(high flow valve) BT7-01 on
DMR-30 (steer left output)

High Torque Position

No signal on DMT-30 or DMR-30.

High Speed Position

BT3-10 on DMT-30 (high speed) is illuminated, BT5-
07 on DMR-30 (shift) is illuminated.

Braking

Brakes are normally locked when the machine is not
in use. Brakes are unlocked by a charge pressure
(380 PSI) from the drive pump. A 12 volt signal is
sent to the brake solenoid by BT5-04 on DMR-30.

Tilt

A 12 volt signal is at BT1-05 (tilt signal input) when
the machine is level. If the machine is out of level or
the level sensor fails, the machine will stop. Red wire
on level sensor is power in, and white wire is signal
out.

Interlocks

There are two interlocks on the machine.
1. Lift Interlock: A12 Volt signal is sent to BT2-01 on

DMR-30; allows high speed travel.

2. Telescope interlock (at tail end of boom): A 12

volt signal is sent to BT1-11 & BT1-12 on DMR-
30 when boom is fully retracted; allows high
speed travel.

«
...
46
47
48
49
50
...
»

Summary of Contents for ab62



















































































































































Reviews:

No comments

Related manuals for ab62

Brand: National Instruments Pages: 8

Brand: fadini Pages: 16

Brand: National Instruments Pages: 13

Brand: National Instruments Pages: 30

Brand: Parkside Pages: 113

Brand: STAYER WELDING Pages: 56

Brand: Barton Pages: 36

Brand: stellar labs Pages: 52

TECHNOMIG 210 DUAL SYNERGIC

Brand: Telwin Pages: 176

Calc-An-Acre II

Brand: micro-trak Pages: 30

Brand: TradeQuip Pages: 7

Brand: Gude Pages: 7

Oxford MAJOR 190

Brand: Sunrise Medical Pages: 48

Brand: Keurig Pages: 6

Brand: JLG Pages: 97

Brand: Demtech Pages: 25

Brand: Thermal Arc Pages: 62

Brand: vistaCNC Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands