Upright ab62 Service And Parts Manual Download Page 28 | Manualshive

Page: 28 / 146

background image

3-10

AB62 Work Platform - European

M

AINTENANCE

Section

3.9

3.9 S

ETTING

H

YDRAULIC

P

RESSURES

Figure 3-14 shows complete hydraulic manifold

assembly.

NOTE: Check hydraulic pressures whenever the

pump, manifold, or any relief valve has been
serviced or replaced.

High Flow Relief Valve (#5)

1. Operate the hydraulic system 10-15 minutes to

warm the oil.

2. Install a 0-3000 PSI pressure gauge to the pres-

sure test port #3-using Part # 063965-002, Quick
Disconnect Adapter.

3. Retract boom completely.
4. While activating the boom retract function, set the

pressure to 186 bar (2700 PSI) maximum by
slowly turning the adjusting screw. Turning the
adjusting screw clockwise increases pressure;
counterclockwise decreases pressure.

5. Remove the pressure gauge, and reinstall all

plugs.

Low Flow Relief Valve (#9)

1. Operate the hydraulic system 10-15 minutes to

warm the oil.

2. Install a 0-207 bar (0-3000 psi) pressure gauge to

the pressure test port.

3. Completely extend jib function.
4. Continue activating function and set the pressure

to 97 bar (1400 psi) by slowly turning the adjust-
ment screw. Turning the adjusting screw clock-
wise increases pressure; counterclockwise
decreases pressure.

5. Remove the pressure gauge, and reinstall all

plugs.

Counterbalance Relief Valves

1. If any counterbalance relief valve is faulty, com-

pletely lower the jib, and retract the boom.

2. Replace or recalibrate the counterbalance valve.
3. Slowly cycle function related to replaced counter-

balance valve several times to remove air from
the system.

«
...
26
27
28
29
30
...
»

Summary of Contents for ab62



















































































































































Reviews:

No comments

Related manuals for ab62

Brand: National Instruments Pages: 9

Brand: Parkside Pages: 94

TRANSITIONS Angled Entry Mat

Brand: EZ-ACCESS Pages: 4

FORCE 125 230V ACD

Brand: Telwin Pages: 104

Origo Arc 4001i

Brand: ESAB Pages: 24

RIS 400PE/PW EKO 3.0

Brand: Salda Pages: 68

Brand: YASKAWA Pages: 45

Brand: Parweld Pages: 16

Brand: Parweld Pages: 16

DuplicAir Intelligent Control Blue

Brand: Jydepejsen Pages: 52

Brand: Daikin Pages: 36

Brand: Miller Pages: 56

Safeline DNSL-IO2

Brand: DINA Pages: 28

GRAND TIG 200 DC PFC MV

Brand: LOKERMANN Pages: 21

SmartStuff SmartBox

Brand: TCP Pages: 2

Brand: M-system Pages: 3

Brand: ANDELI Pages: 23

Brand: IDENTEC SOLUTIONS Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands