Uponor Climate Control-Multifunction Installation Manual Download Page 13

www.uponor-usa.com • www.uponor.ca

20

Uponor Climate Co˘ntrol™ - Multifunction Installation Guide

21

Snow-melt Connections

Climate Co˘ntrol

TM

 - Multifunction supports snow-melt operation through 

the Uponor Snow Melt Control (A9013051). The Snow Melt Control, which 
wires to the main control panel using a Cat5 cable and RJ45 ends for simple 
and easy connections, can plug into any port other than what is reserved 
for boiler connection. This basic snow-melt package allows for slab sensing 
to control the slab temperature for melting. (See 

Figure 4-14

.) An active 

red LED is included on the snow-melt control to indicate when the area is 
heating. A manual button is also included to start a melting cycle if the idle 
feature is not used. Terminals are optional when a remote-mounted switch or 
button is required outside of the mechanical room or area.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Figure 4-14

: Typical snow-melt connection with slab sensing 

Auto

Active

Remote Push

Button (optional)

Top View

Side View

On

Tx

Run

Rx

Port 1

Input 1

Operate

MMI

Port 8

Input 8

Port 3

Port 2

Port 4

Port 5

Input 2

Input 3

Input 4

Input 5

Port 6

Input 6

Port 7

Input 7

Rx

Tx

Intercon

Uponor Snow 

Melt Control 

(A9013051)

10K Slab Sensor

To Climate Co˘ntrol 

Main Panel

The Climate Co˘ntrol - Multifunction System supports automatic snow-melt 
operation when using Uponor Automatic Snow and Ice Sensor (A9013052). 
This package includes a sensor and a socket to detect snow or ice and 
automatically enables the system to start a melting cycle. (See 

Figure 4-15

.) 

Note:

  Other manufacturer snow and ice sensors are not compatible.

Figure 4-15

: Typical snow-melt connection with slab sensing and snow and ice detector

Auto

Active

Remote Push

Button (optional)

Top View

Side View

On

Tx

Run

Rx

Port 1

Input 1

Operate

MMI

Port 8

Input 8

Port 3

Port 2

Port 4

Port 5

Input 2

Input 3

Input 4

Input 5

Port 6

Input 6

Port 7

Input 7

Rx

Tx

Intercon

Uponor Snow 

Melt Control 

(A9013051)

10K Slab Sensor

Dedicated Transformer

24VAC Requirement

(Supplied by others)

Re

d

Bl

ac

k

and Ice Sensor

Automatic Snow 

To Climate Co˘ntrol 

Main Panel

Summary of Contents for Climate Control-Multifunction























Reviews: