background image

AR3016G  Installation and Hardware Reference Manual

  

 

1-8

 

 

AR3016G Components 

 

Figure 1-9: Controller Module Rear Panel 

 

Host ports

: Each controller module has two (2) FC ports (labeled 

FC-

CH0

 and 

FC-CH1

) on the left of the controller module rear panel that 

accept SFP transceivers. The two (2) FC ports should be connected to 

external FC-4G host computer(s). These ports can auto-negotiate the 

speed and determine whether the data transmission rate is 4Gbps, 

2Gbps or 1Gbps.  

The default configurations do not include SFP transceivers on the FC 

ports. You can order the field-replaceable, SFP tranceivers (IFT-

9270CSFP2GA01) from your subsystem vendor or contact them for a 

compatible list.  

 

COM ports

: The controller module comes with two (2) COM ports. 

One port, 

COM1

, is used for accessing the controller-embedded 

configuration utility through the network that allows you to configure 

and monitor your array and upgrade firmware over a VT-100 terminal 

emulation program running on a management computer. An audio 

jack to DB9 cable is shipped with your subsystem to facilitate the 

connection. 

The second COM port, marked as 

COM2

 is for uninterruptible power 

supply (UPS) connection. An optional audio jacks to DB-9 serial 

communication cable (PN: IFT-9270CUPSCab) is available for 

purchase. Please refer to 

Appendix A

 for instructions on connecting a 

UPS.  

 

Ethernet ports

: The controller module on the AR3016G comes with a 

10/100M Ethernet port used for remote management through the 

network. Shielded cables must be used to protect against emissions. 

Connect the other end of the Ethernet cable to a LAN hub port of the 

local network. 

 

LED indicators:

 Each controller board rear panel comes with six (6) 

LED indicators (labeled from 

1

 to 

6

). Please refer to 

Chapter 3

 for 

information on how to monitor your subsystem using the LED 

indicators. 

Summary of Contents for AR3016G

































































































Reviews: