Unitec SSA-003 Manual Download Page 43

Page: 43 / 55

3 Troubleshooting

The buzzer will sound in case of a mistake with the safety device

or paper jamming and the content of it will be shown on the liquid

crystal screen and the machine will be changed to stop or stay at

the standby state.

3-1 safety cover fails

The top cover is off,there will be buzzer sound.

settlement :Turn off the power, put on the top cover, then turn on

the power.

3-2 Settlement of paper jamming

(A) Settle it upon the way below in case of internal paper

jamming

①

Turn off the power.

②

Remove the top cover.

③

Remove the longitudinal cutter assembly and take out the jammed

paper.

④

Put the top cover back on.

⑤

Turn on the power and press <start> key.

⑥

Confirm the jammed paper and chips have been taken out.

⑦

Turn off the power.

⑧

Open the top cover.

⑨

Mount the assembly.

⑩

Put on the top cover.

⑾

Turn on the power and see if there is an abnormal sound.

(B) Settle it upon the way below in case of paper jamming with

the paper feeding tray

①

Turn off the power.

②

Take out the paper piled up on the tray.

PDF

文件使用

"pdfFactory Pro"

试用版本创建

www.fineprint.cn

Summary of Contents for SSA-003
























































Search results

Summary of Contents for SSA-003

Reviews:

Unitec SSA-003, Manual, Page: 43 / 55

Search results

Summary of Contents for SSA-003

Reviews: