Unitec SSA-003 Manual Download Page 10

Page: 10 / 55

（

）

Please make sure of the power switch to be in good

connection.

1-2 The place and conditions where the machine is placed

Please use this machine in the place as below:

●

Horizontally fixed place

●

Well ventilated place

●

Leave a proper workable space around the machine.

●

As this machine is made with a precise mechanism and

electronic elements, a failure may occur with it if used in the

place as below:

●

Direct sunshine

●

Mists often happen

●

Wetted

●

Available with fire

●

Easily made wet by water

●

Close to a cold-warm house

●

Available with vibration

●

Please do not have any other plugs inserted in the socket used

specially for the machine.

●

Use a static-electricity preventing cover and a humidifier for the

place where the static electricity happens easily.

●

Do not place the machine on a table smaller than itself.

PDF

文件使用

"pdfFactory Pro"

试用版本创建

www.fineprint.cn

Summary of Contents for SSA-003
























































Search results

Summary of Contents for SSA-003

Reviews:

Related manuals for SSA-003

Brands by name

Popular brands

Unitec SSA-003, Manual

Search results

Summary of Contents for SSA-003

Reviews:

Related manuals for SSA-003

Brands by name

Popular brands