Unipulse TM201 Operation Manual Download Page 15

Page: 15 / 58

Setting Procedures

Setting Procedures

Chapter

3-1.

USB interface

This USB interface allows the TM201 to be used in the dedicated PC application, such as retrieving
the torque, rotation speed and power of UTM

Ⅱ

, writing setting values into the TM201 and so on.

Communication specifications

Communication standard

USB Ver.2.0 compliant, full speed (12Mbps)

Connector

mini-B TYPE

3-2.

PC preparation

Please make sure to install USB drive and PC application prior to connecting TM201 to the PC for
the first time.

PC operating environment

Windows7

CPU

Core i3

2GHz or above

Display

800×600 pixel or above

Memory

2GB or above

USB port

One or more free ports

Hard disk

15GB free space or more

USB driver

Virtual COM Port (VCP) Drivers (developed by FTDI Limited)

USB driver installation

Online network to perform automatic installation of driver.

Please go online network.
The driver automatically downloaded and installed via the network when TM201 connected to PC
with the USB cable.

In case of failing driver installation or not starting of PC application software, you delete the USB
driver and reconnect to PC. Please try again.
If it doesn't automatically perform installation, see the homepage of FTDI.

Guide

http://www.ftdichip.com/Support/Documents/InstallGuides.htm

Driver

http://www.ftdichip.com/Drivers/VCP.htm

USB connection

Following the installation procedures, connect the USB cable included to the PC.
The USB connector of the TM201 is mini-B TYPE.

Setting Procedures

Summary of Contents for TM201


























































Search results

Summary of Contents for TM201

Reviews:

Related manuals for TM201

Brands by name

Popular brands

Unipulse TM201, Operation Manual

Search results

Summary of Contents for TM201

Reviews:

Related manuals for TM201

Brands by name

Popular brands