background image

13 of 33 

  

 

Power  Supply  &  Signal  (4-20mA)  cable  connections  will  be  on  the 
Right hand side of processor board: 

 
After removing the transmitter glass window cover and Top Processor 
board, go for the power supply & 4-20mA signal wire connections as 
given below. 
 
Locate  3  pin  Green  connector  CN7  on  the  bottom  board.  Pull  cable 
into the enclosure through the cable gland on the right hand side 
of the enclosure as shown in the figure 4.  
 
Connect 3 wires as following: 
 

Positive Supply 

(+24V)

  

: +24 VDC to the labeled terminal. 

Signal 

(

4-20mA

)

:

 4-20mA loop signal to the labeled terminal 

Negative Supply 

(AGND)

   

: Ground wire to the labeled terminal 

 
 
 
Note:  To  avoid  radio  frequency  interference  (RFI),  the  shield 
(including Mylar) must be grounded. Simply tying a bare drain wire 
to  ground  does  not  ground  a  shield.  Keep  a  shield  as  short  as 
possible, tie the shield to the external grounding screw. Also tie 
any unused wires to the Ground. 

 

    

Note:   

 

3-wire connection shall be 
done as below (CN7) 

1.

 

+VE (24V Dc) 

2.

 

4-20mA (sourcing) 

3.

 

NC 

4.

 

-VE (GND) 

 

Summary of Contents for 500DT


































Reviews: