Union Community Virdi 4000 User Manual Download Page 44 | Manualshive

Page: 44 / 60

background image

VIRDI 4000 User Guide

44

Union Community CO., LTd. 44-3 Hyundai Topics Building 5, 6 floor, Bangi-dong,
Songpa-gu, Seoul, Korea 138-050, Tel: 82-2-6488-3000, Fax: 82-2-6488-3099,
E-Mail:[email protected], http://www.unioncomm.co.kr

This is the setting for the card reader connected to a terminal. This shall be set
to ‘0’ except in the following cases:

  - ‘0’: no card reader
  - ‘1’: a low-frequency RF Card reader is installed
  - ‘2’: a high-frequency smart card reader is installed
  - ‘3’: a Wiegand-type card reader is installed (ex.: HID...)
  - ‘4’: a new version of the smart RF reader is installed
  - ‘5’: an external card reader is installed

If this is set to a number other than 0 and [F1]~[F4] or [ENTER] is pressed, only

the authentication mode is changed and 1:N fingerprint authentication is not
performed. However, 1:N authentication is performed only for auto sensing.

Once the setting is complete, press [ENTER] to move to the upper menu.

3.8.3. Fingerprint sensor settings

3.8.3.1. 1:1 verification level settings

◆

[ENTER]

[6]

‘084265’ [ENTER]

[3]

◆

1:1

인증레벨

(1-9):4

Default setting: ‘4’

This  sets  the  matching  rate  between  the  fingerprints  input  and  the  fingerprints
stored in the database of a terminal. The higher the level, the higher the security,
but the possibility of authentication failure is higher.

1:1  identification  level  is  an  authentication  level  setting  menu  used  when
authentication  is  performed  together  with  an  ID.  If  the  entered  ID  is  ‘1234’,  the
fingerprint  registered  with  the  ID  ‘1234’  is  retrieved  from  the  database  to
compare the two fingerprints.

However, in the case of 1:1 authentication, if a user’s 1:1 level is not set to [0]

(1:1 level of the terminal is used), the user’s 1:1 level is used.

Press [ENTER] to move to the next setting.

«
...
42
43
44
45
46
...
»

Summary of Contents for Virdi 4000





























































Reviews:

No comments

Related manuals for Virdi 4000

Brand: Wasp Pages: 16

Brand: Rain Bird Pages: 4

Brand: Rain Bird Pages: 2

Brand: Rain Bird Pages: 140

WeatherSmart RSC600i

Brand: Raindrip Pages: 36

Brand: Velleman Pages: 12

Brand: Casambi Pages: 2

Brand: intech 21 Pages: 15

Brand: Contemporary Research Pages: 22

Touch Screen Controller RX142

Brand: 3M Pages: 29

GVB-8-WP Series

Brand: Genasun Pages: 8

Brand: Melexis Pages: 13

Brand: Omega Engineering Pages: 11

Brand: NI Pages: 28

Brand: National Instruments Pages: 20

Brand: IFM Pages: 3

Smart Home Controller 2.0

Brand: Eaton Pages: 24

DYNALOGIX II DY 4000

Brand: DYNACO Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands