Union Community Virdi 4000 User Manual Download Page 8

Page: 8 / 60

VIRDI 4000 User Guide

Union Community CO., LTd. 44-3 Hyundai Topics Building 5, 6 floor, Bangi-dong,
Songpa-gu, Seoul, Korea 138-050, Tel: 82-2-6488-3000, Fax: 82-2-6488-3099,
E-Mail:[email protected], http://www.unioncomm.co.kr

== 00:00

- A registered user tried authentication

when entry/exit is not allowed.

== 00:00

- Waiting for a reply from the server

for authentication

== 00:00

- Terminal is locked
- No meal time even though the unit is set to meal

control mode

== 00:00

- Terminal program upgrade

(Power switch should not be turned off when this

message is displayed.)

1.5. Voice information during operation

“Please enter your fingerprint”

Enter fingerprint using the fingerprint input
window

“You are authorized”

Authentication successful

“Please try again”

Authentication failed

1.6. Buzzer sound during operation

“ppig”

When a button is pressed or a card is being read
When fingerprint input is completed, allowing the user to
remove his fingerprint

“ppibig”

Authentication failed or wrong user input

“ppiriririck”

Waiting for fingerprint input

“ppiririck”

Authentication successful or settings for the current user are
completed

1.7. LED signal during operation

POWER LED : Power on/off

DOOR LED : Door open/close

CARD LED : Card contact

Summary of Contents for Virdi 4000




























































Search results

Summary of Contents for Virdi 4000

Reviews:

Brands by name

Popular brands

Union Community Virdi 4000, User Manual

Search results

Summary of Contents for Virdi 4000

Reviews:

Brands by name

Popular brands