manualshive.com logo in svg

Union Community Virdi 4000, User Manual

Share
Download
Union Community Virdi 4000 User Manual Download Page 36

 
 
 

VIRDI 4000 User Guide                                                                                                                                           

36

 

Union Community CO., LTd. 44-3 Hyundai Topics Building 5, 6 floor, Bangi-dong,   
Songpa-gu, Seoul, Korea 138-050, Tel: 82-2-6488-3000, Fax: 82-2-6488-3099,   
E-Mail:[email protected], http://www.unioncomm.co.kr 

     

<User ID Group> 
(N=0/Y=1):0 

  Default setting: ‘0’ 

 

Treat  first  digits  of  the  ID  as  a  group  for  authentication,  so  1:N 
authentication  can  be  processed  much  faster  when  over  1,000  users  are 
registered. 
 

If it is set to ‘1’, fingerprint authentication is performed for users starting with 
the  entered  ID.  If it is set  to ‘0’,  treat entered  numbers as  a  user ID  and  try 
user fingerprint and 1:1 authentication for the corresponding ID 

 

Ex.)  when  a  user  ID  is  a  4-digit  number  and  ‘12’  is  entered  for 
authentication, if it is set to ‘1’, 1:N authentication is performed for user 
IDs  ‘1200’~’1299’.  If  it  is  set  to  ‘0’,  1:1  authentication  is  performed  on 
user ID 12 with his/her fingerprint. 

 

 When 1:N authentication is set to ‘0’ 

 

<Verify Multi-FP> 
(N=0/Y=1):0 

  Default setting: ‘0’ 

 

For  successful  authentication,  all  registered  fingerprints  shall  be 
authenticated after ID (or card) input. 
 
This is used when a high security level is required for special areas. If a user 
of ‘ID 0001’ has 3 fingerprints registered to the unit, all 3 fingerprints shall be 
authenticated after ID input.   
 
The  authentication  sequence  for  the  3  fingerprints  does  not  matter  in  this 
case,  but  authentication  fails  if  a  single  fingerprint  is  not  successfully 
authenticated 

 

Once the setting is complete, press [ENTER] to move to the upper menu. 
 

3.5.3. Door settings 
 

In  the  main  menu,  press  [3]  to  select  “3.  Option”  and  the  following  screen 
appears: 
 

1. Application 
2. Verify Option 
3. Set Doorlock 
4. Sound Control 
5. Time Setting 
6. Other Setting

 

 

Press [3] for door settings. 

Summary of Contents for Virdi 4000





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands