manualshive.com logo in svg

Unimig RazorWeld MS500, Operating Manual

Share
Download
Unimig RazorWeld MS500 Operating Manual Download Page 12

12

1.  Warning, watch out. There are possible hazards as shown by the symbols.
2.  Engine fuel exposed to flames or sparks can cause fire or explosion.
3.  Do not smoke while fuelling or if near fuel
4.  Stop engine before fuelling
5.  Do not fuel a hot engine 
6.  Use diesel fuel only.

1.  Warning, watch out. There are possible hazards as shown by the symbols.
2.  Fire hazard from leaking engine fuel. Fire can result from welding on base at  
 

non-designated areas causing a possible fuel leak.

3.  Fuel tank is located inside base.
4.  Do not weld, cut, grind or drill on base of unit.

1.  Warning! Watch out. There are possible hazards as shown by the symbols.
2.  Falling equipment can cause serious injury and damage.
3.  Use lifting eye to lift or move unit only. Use proper equipment when lifting.
4.  Do not use lifting eye to lift and support unit and trailer or other heavy devices  
 

or accessories

1.  Warning, watch out. There are possible hazards as shown by the symbols.
2.  Electric shock from wiring can kill 
3.  Moving parts, such as fans, rotors, and belts, can cut fingers and hands and cause  
 

injury. Keep away from moving parts.

• LIFTING EXTRA WEIGHT CAN

  CAUSE FAILURE TO THE 

  LIFTING EYE RESULTING IN 

  DAMAGE TO UNIT OR INJURY 

  TO PERSONS

WARNING

THIS LIFTING EYE IS DESIGNED

TO LIFT THIS UNIT ONLY

Summary of Contents for RazorWeld MS500





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands