background image

S e c t i o n   3   –   S y s t e m   P r o g r a m m i n g  

  

51

 

Step 2

: Enable the delayed hotline on a single extension 

Switch on delayed hot line and assign to an extension 

GENERAL SETTINGS 

 Hot line assignment 

 Delayed hot line ext

 

Switch off delayed hot line  

GENERAL SETTINGS 

 Hot line assignment 

 Delayed hot line Off

 

Intrusion & Paging Programming 

Description 

It is possible for extensions to intrude on a call if an extension is busy, or to connect in handsfree 
mode directly for terminal extensions, also called paging. Intrusion and paging rights need to be 
programmed for an extension before it is allowed to use the feature. It is not possible to intrude 

upon data protected or fax/modem extensions. When a call is intruded upon, there are two brief 
warning tones at the intrusion start. These tones may be disabled system-wide. 

 

Note: Intrusion and paging rights do not apply to calls to the paging port (dialling 10).  

 

It is not possible to intrude on a data-protected extension. 

Default 

No extensions are allowed to intrude on other calls. Intrusion warning tone is on. 

 

Enable an extension to page and intrude on extensions 

SYSTEM SETTINGS 

 Miscellaneous 

 Intrusion rights 

 Ext 

x Intr. On

 

Disable an extension from paging and intruding on extensions 

SYSTEM SETTINGS 

 Miscellaneous 

 Intrusion rights 

 Ext 

x Intr. Off

 

Switch on intrusion warning tone 

Switch off intrusion warning tone 

ISDN Programming 

206 system supports ONE basic rate ISDN access and 208/212 system supports up to 2 basic rate 
ISDN accesses if the optional ISDN cards are fitted. MSN and DDI numbering is supported by the 
telephone system. 

In the case of MSN calls an incoming call will ring at the programmed extension for 30 seconds after 
which it will become a general incoming call - ringing at all extensions normally programmed to ring 

on general calls. It is possible to override this default setting and program any combination of 
extensions to ring on any MSN number, the procedure is detailed in ‘Ringing Settings’ on page 53. 
The programmed MSN number and the incoming MSN number may have different lengths, in this 
case the system looks at the shorter number and compares it with the last digits of the longer 
number. 

CLIP data and CLIR status are sent to the ISDN network when an outgoing call is made. COLP 
data and COLR status are sent to the network when a call is answered. 

When an extension sets up or answers an external call the CLIP/COLP data is based on the MSN 
number programmed for the extension. If there is no MSN number programmed then the base 
number for that particular ISDN line is used. If there is no base number programmed then no 

CLIP/CLIR data is sent, though the network may add its own later. In the case of external call 
diversion and external alarm calls the ISDN base number for the line is used. 

 

Note: After installing or changing the lines from point to point to point to multipoint the 
system should be powered off after a delay of six minutes and then powered up while 
connected to the S bus to correctly establish ISDN settings. 

 

 ext 

 

 PIN 

 ext1, ext2,… ext n 

 PIN 

 ext1, ext2,… ext n 

 

 

Summary of Contents for Home Office

































































































Reviews: