background image

44

3.17.2 - AUDIBLE ALARMS

MAXIMUM TEMPERATURE 
AUDIBLE ALARM

The boiler triggers an audible alarm when it is overheated.

The temperature threshold is set in parameter 2, which is pre-
configured at 88°C by the printed circuit board.

It can happen that, in certain cases, the working temperature 
of the boiler has to be set much higher (e.g. unit heaters or fan 
coils situated far from the boiler) than parameter 1 (working 
temperature 82°C).
In this case, the overheating audible alarm could be triggered 
frequently.
It is advisable to set parameter 2 (max temperature for thermal 
inertia in boiler) at a higher value of up to 90°C.
If instead the alarm is triggered without the boiler overheating, 
the cause may be an operating fault of the system like excess 
draught in the flue, obstruction of the system or storage tank 
pump, obstruction of the recirculation pump, or a defect with the 
printed circuit board.

Advice for the user:

 if it is necessary to set a working 

temperature of more than 80°C, it is advisable to proportionally 
increase parameter 2 (max temperature for thermal inertia in 
the boiler).

PROBE AUDIBLE ALARM

The boiler has an intermittent alarm system that signals one or 
more faults with the probes due to these being disconnected or 
out of range; in any case, a message is displayed on the screen 
referring to the probe or probes (in order) that are defective or 
disconnected or out of range (e.g. "Probe S4 disconnected"). 
If the temperature to which the probes are subjected is out of 
range, you need to wait for the temperature to return to a normal 
level. Replace the probe if you are certain the temperature is 
not out of range.

If the problem relates to the connection of a probe, and the 
message on the display indicates that a probe is disconnected, 
check the connection concerned: if the probe is disconnected, 
simply reconnect it; but if it is connected, despite the alarm 
message, contact the assistance centre because the probe is 
clearly defective.

Summary of Contents for ALLBIOMIX

















































Reviews: