UNI-T UPO1000CS Series User Manual Download Page 82

Page: 82 / 99

14. Mathematical Operation

14.1

Mathematical Function

14.2 FFT

14.3 Logical Operation

14.4 Digital Filter

14.5 Advanced Operation

UPO1000CS series digital phosphor oscilloscope carries a variety of mathematical operations, it includes

math, FFT, logical operation, digital filter and advanced operation.

Enter mathematical operation menu, adjusting POSITION or SCALE knob on vertical control area to

change the vertical position and the vertical scales of the waveforms. The math operation waveforms

cannot be independent adjust the horizontal time base scale. it will change automatically according to the

horizontal time base scale of the analog input channel.

Math operation cursor

marks the result of a mathematical operation.

Summary of Contents for UPO1000CS Series




































































































Search results

Summary of Contents for UPO1000CS Series

Reviews:

Related manuals for UPO1000CS Series

Brands by name

Popular brands

UNI-T UPO1000CS Series, User Manual

Search results

Summary of Contents for UPO1000CS Series

Reviews:

Related manuals for UPO1000CS Series

Brands by name

Popular brands