manualshive.com logo in svg

UFactory xArm 5, User Manual

Share
Download
UFactory xArm 5 User Manual Download Page 93

93

Note:

Before friction identification, please read the software tips carefully and strictly

follow the software guidelines for friction identification.

Advanced Logic

Clear the IO output when the robot is stopped

After turning on

【

Clear IO output when the robot is stopped

】

if the robotic arm

receives a stop command,

【

Controller Digital Output

】

or

【

Tool Digital Output

】

will be set to the invalid state. Otherwise, the

【

Controller Digital Output

】

or

【

Tool

Digital Output

】

will not be affected by the stop command.

Collision Rebound

●

When this mode is turned on, the robotic arm will rebound backward for a certain

distance after it collides with an obstacle. If collision sensitivity is not zero, when
this mode is turned off, the robotic arm will stay at the position where collision is
detected.

Self-collision detection

●

When the mode is turned on, it will prevent the xArm from causing self-collision.

Summary of Contents for xArm 5























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands