UCL SWIFT TEK-3 Training Manual Download

Page: 27 / 29

3330 Earhart Drive, Suite 208

Carrollton, TX 75006

Office: 972.556.0916

Fax: 972.910.8384

OPM1

REFERENCING SETUP

The LSMM output power is calibrated to -22dBm. If the OPM1 screen displays between -22.00dBm and

-25.00dBm, press and HOLD the dB/dBm button for 5 seconds. After 5 seconds, release the dB/dBm button. The

OPM1 screen will display 0.00dB, with some minor variation. DO NOT switch the OPM1 back to the dBm mode.

SETTING REFERENCE

Page 4

M-UM038-01 RP 460 Reference and Test

DMT

Referencing Setup
The connectors on the Test Jumper should be cleaned to appropriate standards. Use an inspection

scope to verify fiber cleanliness. Plug the connectors on the Test Jumper into the RP 460 and DLS 355.

The RP 460 should be in the dBm measurement mode. If it is not in the dBm mode, press the dB/dBm

button once to put it into the dBm mode.

Setting Reference
The DLS 355 output power is calibrated to -5dBm. If the RP 460 screen displays between -5.00dBm

and -7.00dBm, press and HOLD the dB/dBm button for 5 seconds. After 5 seconds, release the

dB/dBm button. The RP 460 screen will display 0.00dB, with some minor variation. DO NOT switch the

RP 460 back to the dBm mode.

Between -5.00 and -7.00dBm

Hold for 5 seconds

Reference is set

Loss Test
The Test Jumper MUST remain attached to the DLS 355. Do not remove the Test Jumper from the

optical link. The connectors on the Test Jumper and the Fiber-Under-Test should be cleaned to

appropriate standards. Use an inspection scope to verify fiber cleanliness. Plug the Test Jumper

into one end of the Fiber-Under-Test using a bulkhead adapter as shown. Plug the other end of the

Fiber-Under-Test into the LC adapter on the RP 460. The Insertion Loss of the Fiber-Under-Test will be

shown on the RP 460 screen.

Page 4

M-UM038-01 RP 460 R

efer

ence and T

est

DMT

Refer

encing Setup

The connectors on the T

est Jumper should be cleaned to appropriate standards. Use an i

nspection

scope to verify fiber cleanliness. Plug the connectors on the T

est Jumper into the RP 460 and DLS 355.

The RP 460 should be in the dBm measurement mode. If it is not

in the dBm mode, press the dB/dBm

button once to put it into the dBm mode.

Setting R

efer

ence

The DLS 355 output power is calibrated to -5dBm. If the RP 460

screen displays between -5.00dBm

and -7.00dBm, press and HOLD the dB/dBm button for 5 seconds. A

fter 5 seconds, release the

dB/dBm button. The RP 460 screen will display 0.00dB, with some

minor variation. DO NO

T switch the

RP 460 back to the dBm mode.

Betw

een -5.00 and -7.00dBm

Hold for 5 seconds

Refer

ence is set

Loss T

est

The T

est Jumper MUST remain attached to the DLS 355. Do not remove t

he T

est Jumper from the

optical link. The connectors on the T

est Jumper and the Fiber-Under-T

est should be cleaned to

appropriate standards. Use an inspection scope to verify fiber c

leanliness. Plug the T

est Jumper

into one end of the Fiber-Under-T

est using a bulkhead adapter as shown. Plug the other end of th

Fiber-Under-T

est into the L

C adapter on the RP 460. The Insertion Loss of the Fiber-Under-

Test will be

shown on the RP 460 screen.

OPM1

Between -22 and -25dBm

Page 4

M-UM038-01 RP 460 Reference and Test

DMT

Referencing Setup
The connectors on the Test Jumper should be cleaned to appropriate standards. Use an inspection

scope to verify fiber cleanliness. Plug the connectors on the Test Jumper into the RP 460 and DLS 355.

The RP 460 should be in the dBm measurement mode. If it is not in the dBm mode, press the dB/dBm

button once to put it into the dBm mode.

Setting Reference
The DLS 355 output power is calibrated to -5dBm. If the RP 460 screen displays between -5.00dBm

and -7.00dBm, press and HOLD the dB/dBm button for 5 seconds. After 5 seconds, release the

dB/dBm button. The RP 460 screen will display 0.00dB, with some minor variation. DO NOT switch the

RP 460 back to the dBm mode.

Between -5.00 and -7.00dBm

Hold for 5 seconds

Reference is set

Loss Test
The Test Jumper MUST remain attached to the DLS 355. Do not remove the Test Jumper from the

optical link. The connectors on the Test Jumper and the Fiber-Under-Test should be cleaned to

appropriate standards. Use an inspection scope to verify fiber cleanliness. Plug the Test Jumper

into one end of the Fiber-Under-Test using a bulkhead adapter as shown. Plug the other end of the

Fiber-Under-Test into the LC adapter on the RP 460. The Insertion Loss of the Fiber-Under-Test will be

shown on the RP 460 screen.

Hold for 5 seconds

Reference is set

The Test Jumper MUST remain attached to the LSMM. Do not remove the Test Jumper from the optical link.

The connectors on the Test Jumper and the fiber-under-test should be cleaned to appropriate standards. Use

an inspection scope to verify fiber cleanliness. Plug the Test Jumper into one end of the fiber-under-test using

a bulkhead adapter as shown. Plug the other end of the fiber-under-test into the LC adapter on the OPM1. The

Insertion Loss of the fiber-under-test will be shown on the OPM1 screen.

LOSS TEST

The connectors on the Test Jumper should be cleaned to appropriate standards. Use an inspection scope to

verify fiber cleanliness. Plug the connectors on the Test Jumper into the OPM1 and LSMM. The OPM1 should

be in the dBm measurement mode. If it is not in the dBm mode, press the dB/dBm button once to put it into the

dBm mode.

3330 Earhart Drive, Suite 208

Carrollton, TX 75006

Office: 972.556.0916

Fax: 972.910.8384

PAGE 9

Page 10

M-UM038-01 RP 460 Reference and Test

DMT

Referencing Setup
The connectors on the Test Jumper should be cleaned to appropriate standards. Use an inspection

scope to verify fiber cleanliness. Plug the connectors on the Test Jumper into the RP 460 and DLS 350.

The RP 460 should be in the dBm measurement mode. If it is not in the dBm mode, press the dB/dBm

button once to put it into the dBm mode.

Setting Reference
The DLS 350 output power is calibrated to -22dBm. If the RP 460 screen displays between -22.00dBm

and -25.00dBm, press and HOLD the dB/dBm button for 5 seconds. After 5 seconds, release the

dB/dBm button. The RP 460 screen will display 0.00dB, with some minor variation. DO NOT switch the

RP 460 back to the dBm mode.

Between -22 and -25dBm

Hold for 5 seconds

Reference is set

Loss Test
The Test Jumper MUST remain attached to the DLS 350. Do not remove the Test Jumper from the

optical link. The connectors on the Test Jumper and the Fiber-Under-Test should be cleaned to

appropriate standards. Use an inspection scope to verify fiber cleanliness. Plug the Test Jumper

into one end of the Fiber-Under-Test using a bulkhead adapter as shown. Plug the other end of the

Fiber-Under-Test into the LC adapter on the RP 460. The Insertion Loss of the Fiber-Under-Test will be

shown on the RP 460 screen.

Test

Jumper

Fiber-Under-Test

Page 10

M-UM038-01 RP 460 Reference and Test

DMT

Referencing Setup
The connectors on the Test Jumper should be cleaned to appropriate standards. Use an inspection

scope to verify fiber cleanliness. Plug the connectors on the Test Jumper into the RP 460 and DLS 350.

The RP 460 should be in the dBm measurement mode. If it is not in the dBm mode, press the dB/dBm

button once to put it into the dBm mode.

Setting Reference
The DLS 350 output power is calibrated to -22dBm. If the RP 460 screen displays between -22.00dBm

and -25.00dBm, press and HOLD the dB/dBm button for 5 seconds. After 5 seconds, release the

dB/dBm button. The RP 460 screen will display 0.00dB, with some minor variation. DO NOT switch the

RP 460 back to the dBm mode.

Between -22 and -25dBm

Hold for 5 seconds

Reference is set

Loss Test
The Test Jumper MUST remain attached to the DLS 350. Do not remove the Test Jumper from the

optical link. The connectors on the Test Jumper and the Fiber-Under-Test should be cleaned to

appropriate standards. Use an inspection scope to verify fiber cleanliness. Plug the Test Jumper

into one end of the Fiber-Under-Test using a bulkhead adapter as shown. Plug the other end of the

Fiber-Under-Test into the LC adapter on the RP 460. The Insertion Loss of the Fiber-Under-Test will be

shown on the RP 460 screen.

Test Jumper

Page 12

M-UM038-01 RP 460 Reference and Test

DMT

Referencing Setup
The connectors on the Test Jumper and loopback should be cleaned to appropriate standards. Use

an inspection scope to verify fiber cleanliness. Plug the connectors on the Test Jumper into the RP

460 and DLS 350. Plug the loopback adapter on to the paired LC side of the Test Jumper. The RP 460

should be in the dBm measurement mode. If it is not in the dBm mode, press the dB/dBm button

once to put it into the dBm mode.

Loss Test
The paired Test Jumper MUST remain attached to the DLS 350 and RP 460. Do not remove the Test

Jumper from the optical link. The connectors on the Test Jumper and the Fiber-Under-Test should be

cleaned to appropriate standards. Use an inspection scope to verify fiber cleanliness. Plug the clipped

LC end of the Test Jumper into one end of the Fiber-Under-Test using the bulkhead as shown. Plug

the loopback on to the other end of the Fiber-Under-Test. The Insertion Loss of the Fiber-Under-Test

will be shown on the RP 460 screen.

Setting Reference
The DLS 350 output power is calibrated to -22dBm. If the RP 460 screen displays between -22.00dBm

and -25.00dBm, press and HOLD the dB/dBm button for 5 seconds. After 5 seconds, release the

dB/dBm button. The RP 460 screen will display 0.00dB, with some minor variation. DO NOT switch the

RP 460 back to the dBm mode.

Between -22 and -25dBm

Hold for 5 seconds

Reference is set

Summary of Contents for TEK-3






























Search results

Summary of Contents for TEK-3

Reviews:

Related manuals for TEK-3

Brands by name

Popular brands

UCL SWIFT TEK-3, Training Manual

Search results

Summary of Contents for TEK-3

Reviews:

Related manuals for TEK-3

Brands by name

Popular brands