UCL SWIFT TEK-3 Training Manual Download

Page: 17 / 29

PAGE 6

3330 Earhart Drive, Suite 208

Carrollton, TX 75006

Office: 972.556.0916

Fax: 972.910.8384

This product conforms with health, safety, and environmental protection standards for products sold within

the European Economic Area (EEA). This product was tested by an ISO 17025 accredited laboratory and

complies with the following CE directives and standards listed below:

DIRECTIVES:

Electromagnetic Compatibilities (2014/30/EU)

STANDARDS: EMC: EN 61326-1:2013 Industrial;

Safety: EN/IEC61010- 1:2010+A1:2016

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)

this device may not cause harmful interference, and

(2)

this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter-

ference in a residential installation. This equipment generates, uses and can radiate radio frequency energy,

and if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help

CERTIFICATIONS

OPM1

uclswiftna.com

Office: 972.556.0916
Fax: 972.910.8384

CONTACT

Summary of Contents for TEK-3






























Search results

Summary of Contents for TEK-3

Reviews:

Related manuals for TEK-3

Brands by name

Popular brands

UCL SWIFT TEK-3, Training Manual

Search results

Summary of Contents for TEK-3

Reviews:

Related manuals for TEK-3

Brands by name

Popular brands