UCL SWIFT TEK-3 Training Manual Download

Page: 26 / 29

PAGE 8

3330 Earhart Drive, Suite 208

Carrollton, TX 75006

Office: 972.556.0916

Fax: 972.910.8384

OPM1

EXAMPLE 4:

MULTIMODE FIBER, POINT-TO-POINT, 1 JUMPER

Fiber Type
Connectors Used
Test Jumper Setup
OPM Used
OLS Used

Multimode

(1) Simplex SC/LC
OPM1
LSMM

Page 3

M-UM038-01 RP 460 Reference and Test

DMT

Example 1: Singlemode Fiber, Point-to-Point, 1 Jumper

Fiber Type

Singlemode

Connectors Used

Test Jumper Setup

Single

OPM Used

RP 460

OLS Used

DLS 355

Fiber-Under-Test
The fiber-under-test is singlemode with LC

connectors on each end. The fiber-under-test may

be up to 250 kilometers long. In this example, the

fiber-under-test is 400 meters long.

Test Jumper
The test jumper is a one-meter singlemode fiber

with SC and LC connectors. The SC connector will

be plugged into the DLS 355 laser source and the

LC connector will be used to interface with the

fiber-under-test.

Power Meter
The RP 460 power meter is set to the

1550nm wavelength. The 1310nm

wavelength may also be used. Always

match the wavelength on the RP 460

to the wavelength on the DLS 355. The

adapter on the RP 460 is the AC 029 LC

adapter.

Light Source
The DLS 355 laser source is set to the

1550nm wavelength. The 1310nm

wavelength may also be used. The

adapter is the default AC 022B SC adapter.

400m Fiber

1m Jumper

The fiber-under-test is multimode with LC connectors on

each end. In this example, the fiber-under-test is

400 meters long.

TEST JUMPER

The test jumper is a one-meter multimode fiber with SC

and LC connectors. The SC connector will be plugged

into the LSMM LED source and the LC connector will be

used to interface with the fiber-under-test.

POWER METER

The OPM1 power meter is set to the 850nm

wavelength. The 1300nm wavelength may also be

used. Always match the wavelength on the OPM1 to

the wavelength on the LSMM. The adapter on the OPM1

is the OPAL LC adapter.

LIGHT SOURCE

The LSMM LED source is set to the 850nm

wavelength. The 1300nm wavelength may also be

used. The adapter is the default OPAS SC adapter.

FIBER-UNDER-TEST

Page 9

M-UM038-01 RP 460 Reference and Test

DMT

Example 4: Multimode Fiber, Point-to-Point, 1 Jumper

Fiber Type

Multimode

Connectors Used

Test Jumper Setup

Single

OPM Used

RP 460

OLS Used

DLS 350

Fiber-Under-Test
The fiber-under-test is multimode with LC

connectors on each end. In this example, the

fiber-under-test is 400 meters long.

Test Jumper
The test jumper is a one-meter multimode fiber

with SC and LC connectors. The SC connector will

be plugged into the DLS 350 LED source and the

LC connector will be used to interface with the

fiber-under-test.

Power Meter
The RP 460 power meter is set to

the 850nm wavelength. The 1300nm

wavelength may also be used. Always

match the wavelength on the RP 460

to the wavelength on the DLS 350. The

adapter on the RP 460 is the AC 029 LC

adapter.

Light Source
The DLS 350 LED source is set to the

850nm wavelength. The 1300nm

wavelength may also be used. The

adapter is the default AC 022B SC adapter.

400m Fiber

1m Jumper

Summary of Contents for TEK-3






























Search results

Summary of Contents for TEK-3

Reviews:

Related manuals for TEK-3

Brands by name

Popular brands

UCL SWIFT TEK-3, Training Manual

Search results

Summary of Contents for TEK-3

Reviews:

Related manuals for TEK-3

Brands by name

Popular brands