background image

ADA15IM

11

ADA SERIES

Figure 16

10. Remove three plastic screw plugs 

(Figure 17)

 from 

hinge holes, top of cabinet, opposite side. Be careful 
not to scratch cabinet.

11. Place door on lower hinge pin. Invert and install upper 

hinge on door.

Figure 17

12. Fasten upper hinge to unit (three screws) 

(Figure 18)

Partially tighten screws.

13. Adjust door to assure proper seal. Tighten upper and 

lower hinge screws securely.

14. Replace three plastic plugs removed in Step 10 into 

holes on top of unit. Replace screws in holes in bottom 
of unit on opposite side.

15. Replace the grille and grille cap. Be sure to place grille 

cap on opposite side of unit from where it was 
originally

.

Before Calling for Service

If your U-Line product appears to be malfunctioning, read 
through the OPERATION section of this guide to ensure 
that the function of all controls are clearly understood. If 
the malfunction persists, the TROUBLESHOOTING GUIDE 
in this guide will assist you in quickly identifying common 
problems, and provide information on possible causes and 
remedies. Most often, this will resolve the problem 
without the need to call for service. 

If Service is Required

If you do not understand a troubleshooting remedy, or 
your product needs service, contact U-Line Corporation 
directly. Contact information appears on the rear cover of 
this guide.

You will be asked for your product Model and Serial 
Numbers. This information should be recorded inside the 
front cover of this guide, following the products original 
purchase. It also appears on the Model and Serial number 
plate located on the upper right or rear wall of the 
interior of your product. 

Replacement Parts

When you need replacement parts, always request that 
genuine U-Line replacements be used. U-Line products 
have been designed and engineered using components 
that work efficiently, and provide superior service life and 
performance. The use of aftermarket parts or components 
may affect the safety, operation, performance or 
durability of your product, and may also void its warranty.

ULIN_0144_A

ULIN_0145_A

6 Service

Summary of Contents for ADA SERIES

















Reviews: