TYAN S2927 Manual Download Page 64

Page: 64 / 88

http://www.tyan.com

Feature

Option

Description

Boot Settings Configuration

Enabled

Quick Boot

Disabled

This option allows user bypass BIOS
self test during POST.

Disabled

Quiet Boot

Enabled

Disabled: displays normal POST
messages.
Enabled: displays OEM log instead of
POST messages.

Force BIOS

Add On ROM Display
Mode

Keep Current

Allows user to force BIOS/Option ROM
of add-on cards to be displayed during
quiet boot.

Boot up Num-Lock

Off

Selects Power-on state for Numlock.

Enabled

Disabled

PS/2 Mouse Support

Auto

Selects support for PS/2 Mouse.

Enabled

Wait for ‘F1’ If Error

Disabled

Waits for F1 key to be present if error
occurs.

Enabled

Hit ‘DEL’ Message Display

Disabled

Displays “Press DEL to run Setup” in
POST.

Disabled

Interrupt 19 Capture

Enabled

Enabled: allows option ROMs to trap
interrupt 19.

Disabled

Endless Boot

Enabled

Endless loop boot from BBS table.

Summary of Contents for S2927

























































































Search results

Summary of Contents for S2927

Reviews:

Related manuals for S2927

Brands by name

Popular brands

TYAN S2927, Manual

Search results

Summary of Contents for S2927

Reviews:

Related manuals for S2927

Brands by name

Popular brands