TYAN S2927 Manual Download Page 52

Page: 52 / 88

http://www.tyan.com

3.7.6 APM Configuration

BIOS Setup Utility

Main

Advanced

PCI/PnP Boot Security Chipset Exit

Resume On PME# [Disabled]

Resume On PCIE Wake# [Disabled]
Resume On LAN (MAC) [Disabled]
Resume On PS/2 Keyboard [Disabled]
Resume On RTC Alarm [Disabled]

Restore on AC Power Loss

[Last State]

Disable/Enable PME to
generate a wake event.

←

→

Select Screen

↑↓

Select Item

+/- Change Option
F1 General Help
F10 Save and Exit
ESC Exit

Feature

Option

Description

APM Configuration

Disabled

Resume On PME#

Enabled

Disable/Enable PME to generate a
wake event.

Disabled

Resume On PCIE Wake#

Enabled

Disable/Enable PME to generate a
wake event.

Disabled

Resume On LAN (MAC)

Enabled

Enable/Disable LAN (MAC) to
generate a wake event.

Disabled

Resume On PS/2 Keyboard

Enabled

Enable/Disable PS/2 keyboard to
generate a wake event

Disabled

Resume On RTC Alarm

Enabled

Enable/Disable RTC event to wake
after a power failure.

Last State

Power on

Restore on AC Power Loss

Power off

Summary of Contents for S2927

























































































Search results

Summary of Contents for S2927

Reviews:

Related manuals for S2927

Brands by name

Popular brands

TYAN S2927, Manual

Search results

Summary of Contents for S2927

Reviews:

Related manuals for S2927

Brands by name

Popular brands