TYAN S2927 Manual Download Page 54

Page: 54 / 88

http://www.tyan.com

3.7.8 Hardware Health Configuration Sub-Menu

You can use this screen to view the Hardware Health Configuration Settings.

Use the up and down arrow (

) keys to select an item. Use the Plus and

Minus (+/-) keys to change the value of the selected option. The settings are
described on the following pages.

BIOS Setup Utility

Main

Advanced

PCI/PnP Boot Security Chipset Exit

Hardware Health Configuration

H/W Health Function

CPUFAN1, CPUFAN2 PWR Control
FAN3, FAN4 PWR Control
FAN Fail LED Indicator

Hardware Health Event Monitoring

[Enabled]

[Disabled]
[Disabled]
[Disabled]

Mainboard Voltages Report

CPU1 Temperature
CPU2 Temperature
Ambient (Near SuperIO) Temp
Ambient (Near VGA) Temp
Ambient (Near MCP55) Temp

CPU1 FAN1 Speed (TACH1)
CPU2 FAN2 Speed (TACH2)
FAN3 Speed (TACH5)
FAN4 Speed (TACH6)

:xx C/ xxx F
:xx C/ xxx F
:xx C/ xxx F
:xx C/ xxx F
:xx C/ xxx F

:xxxx RPM
:xxxx RPM
:xxxx RPM
:xxxx RPM

Enables Hardware
Health Monitoring
Device.

←

→

Select Screen

↑↓

Select Item

+/- Change Option
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit

Feature

Option

Description

Hardware Health Configuration

Enabled

H/W Health Function

Disabled

Enables Hardware Health Monitoring Device.

Enabled

CPUFAN1, CPUFAN2
PWR Control

Disabled

FAN power duty cycle is auto dynamic
programmed in selected temperature range.
Disabled: Fan Power On.
Enabled: Fan Power Duty Cycle=30%(40

C)-

100%(60

C), see max (CPU1, CPU2,

SuperIO)

Enabled

FAN3, FAN4
PWR Control

Disabled

FAN power duty cycle is auto dynamic
programmed in selected temperature range.
Disabled: Fan Power On.
Enabled: Fan Power Duty Cycle=30%(40

C)-

100%(60

C), see max (VGA, MCP55)

Enabled

FAN Fail LED
Indicator

Disabled

Enabled: Any FAN speed less than 800 RPM, the
FAN Fail LED will be lighted.

Summary of Contents for S2927

























































































Search results

Summary of Contents for S2927

Reviews:

Related manuals for S2927

Brands by name

Popular brands

TYAN S2927, Manual

Search results

Summary of Contents for S2927

Reviews:

Related manuals for S2927

Brands by name

Popular brands