TYAN S2927 Manual Download Page 13

Page: 13 / 88

http://www.tyan.com

J2: 3-pin Fan Connector

Use this header to connect the chassis cooling fan to
your motherboard to keep the system stable and
reliable.

Pin 1

Pin 2

Pin 3

GND

+12V

J4/J9/J17/J19: 4-pin FAN Connector with speed control

J9/J17/J19

Use these headers to connect the cooling fans to your
motherboard to keep the system stable and reliable.

Pin 1

Pin 2

Pin 3

Pin 4

GND

+12V

Tachometer

Speed Control

This connector supports the tachometer monitoring and
auto fan speed control.

J35: IPMB Pin Header

Use this header to connect to the IPMB device.

Pin 1

Pin 2

Pin 3

Pin 4

IPMB DATA

GND

IPMB CLK

J31: Front Panel Header

The motherboard provides one front panel header for electrical connection to
the front panel switches and LED’s.

PWR LED+

PWR LED

PWR SW#

Warning LED

KEY

GND

INTRUDER

HDD LED+

HDD LED

Reset

NMI

+5VSB

SMBUS Data

SMBUS

Clock

Summary of Contents for S2927

























































































Search results

Summary of Contents for S2927

Reviews:

Related manuals for S2927

Brands by name

Popular brands

TYAN S2927, Manual

Search results

Summary of Contents for S2927

Reviews:

Related manuals for S2927

Brands by name

Popular brands